User manual HAIER HW-C1270TVE-F SERVICE MANUAL

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual HAIER HW-C1270TVE-F. We hope that this HAIER HW-C1270TVE-F user guide will be useful to you.

Lastmanuals help download the user guide HAIER HW-C1270TVE-F.


Mode d'emploi HAIER HW-C1270TVE-F
Download
Manual abstract: user guide HAIER HW-C1270TVE-FSERVICE MANUAL

Detailed instructions for use are in the User's Guide.

[. . . ] Humanistic design for control panel to help expedient operation Five sentences for tech-support: I. No need to be worried because of the function of intelligent-memory II. Satisfied to encourage children's curiosity because of the child-lock III. [. . . ] If it is, then repair and check computer board and wire as followed. N Check if drain pump acts by touching pump position N Check if drain pump or drain pipe is jammed, and open the filter and clean Y 16 Front Load Washing Machine Cut off the power and choose spin program to start, then check the import voltage of drain pump, is it between AC 220-240 V?Y N Cut off power and pull out water level pressure switch wire connection. Check the export voltage to drain pump, is it between AC 220-240V?between blue wire and green wire Model:HW-C70TVE SERIES Replace drain pump Y The wire between computer board and drain pump is not connected properly. Replace the wire. N Replace PCB (Fig1) Error message:Temperature sensor is not properly connected or damaged (display at the end of a program). Troubleshooting: Cut off power and measure the resistance N of temperature sensor by multimeter, is it between 5-14k?Y NTC exist open circuit . Replace it Check if NTC is connected properly N Y Connect NTC well Check the blue wire and black wire of NTC, are they connected well?N Y Connect all wires well Disconnect the white wire and black wire from computer board, and measure if the resistance between blue wire and black wire of PCB is it infinite?N Replace wire Y Replace PCB 17 Front Load Washing Machine Model:HW-C70TVE SERIES Error message :The heater may be broken Troubleshooting: Cut off power , check the resistance Of two pins of heater element by multimenter is it between 30-35 ?Y Heater element must be broken please replace it N Turn on power , and set wash mode, then start , check the export voltage of heater element between 12-6 and J9-9 , is it between AC 220-240V? Y PCB must be broken, please replace it Error message:The required water level is not reached within 8 min. Troubleshooting: Check if water is leaking from washer bottom. drain pipe or other pipe connection N Check if tap is closed or water pressure is too low (usual between0. 03 -1 MPa) N Clean inlet valve Check if inlet valve is jammed Y Open the tap or wait for normal water pressure to use Y Readjust or replace the broken parts Y N 18 Front Load Washing Machine Model:HW-C70TVE SERIES Observe if the height of Draw out the dispenser and check if water is entering Y N drain pipe not reach 80 cm. If water level pressures switch and the hose is leaking gas Turn on power, and set pre-wash mode, then start. Check the import voltage of electromagnetic valve by multimeter , is it between AC 220-240V between the white wire and red wire that they are not connected?Voltage is220-240V between white wire and white wire, between red wire and red wire Y Electromagnetic valve must be broken, please replace it. N The wire connected PCB and inlet valve is not Check if export voltage from computer board to electromagnetic valve, is it between AC 220-240V that voltage between grown wire and white wire of PCB ?Please reconnect it or replace it. (Fig 2) Replace PCB 19 Front Load Washing Machine Model:HW-C70TVE SERIES Error message:Motor speed error . it may be not properly connected or damaged. Troubleshooting : Connect them well and test. N connected well Cut off power, and check if motor wire is Y Connect them properly and test. Check if the wire of motor is connected well with computer board. N Y Pull out the motor insert string, and check the resistance of motor speed measurer and the Replace the motor. [. . . ] Y Clean N Dismantle the screws Is there foreign material in the washer?N Y Adjust adjustable feet Is washer in balance?N Are the screws of counterweight and motor loose? [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HAIER HW-C1270TVE-F

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual HAIER HW-C1270TVE-F will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag