User manual HAIER KDW24FI

[. . . ] Domestic Dishwasher KDW24FI/B GB Code:0120504283 Safety Is a Good Habit to Get Into NOTICE Carefully read the instructions contained in this manual, as they provide important information which is essential to safe and proper installation, use and maintenance of the appliance. GB - Keep detergents out of the reach of children, who must also be kept away from the dishwasher when it is open. - This appliance cannot be installed outdoors, not even if the area in which it is installed is covered by a roof; it is also very dangerous to leave it exposed to the rain and elements. - Do not touch the heating element during or after a wash cycle. - Do not lean or sit on the door when it is open, as this could overturn the dishwasher. [. . . ] This will eliminate the need for extra wash cycles. Pull out the rack to facilitate loading the dishwasher. Lower Rack Upper Rack How to Use the Lower Rack We recommend that you place the most difficult to clean items on the bottom rack: pots, lids, serving dishes and bowls, as shown in the figure to the right. It is preferable to place serving dishes and lids on the sides of the racks in order to avoid blocking the rotation of the top spray arm. - Deep pots should be slanted to allow the water to flow out. Open the door, turn off the appliance using the ON/OFF switch and turn off the water supply to the unit. Wait a few minutes before removing the dishes so as to avoid handling them while still hot (when they are more susceptible to breakage) and to get better drying results. Setting The Start Delay Time Open the door of the dishwasher partially. If the "C" button is pressed (see, Close-up View" Control Panel"). The start time for the wash cycle can be delayed for 2, 4 or 6 hours. Each time the button is pressed, the "D" light will come on indicating the length of the delay. After selecting the delay time, the wash cycle can be set, as explained in "Starting a wash cycle. . . " There will be a short acoustic signal, and at this point the delay period will begin to count down. During this period the delay indicator light (D) will blink. At the end of the delay time, the indicator will stop blinking and the cycle will start. Cancelling or modifying a cycle while underway Premise: A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the detergent may have already been used, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled, "Loading the Detergent"). NOTE: a) During the delay period, none of the settings can be modified. If necessary, they can be cancelled by pressing cycle selector "P" for about 5 seconds. b) If the power to the appliance goes off or the door is opened during the delay period, the clock will stop the countdown. It will start again when the power has come back on, or when the door has been closed. To change the cycle currently underway, open the door, press the "P" programming button and hold it in for about 5 seconds. Once the cycle has been cancelled, the dishwasher will emit a short acoustic sound and the relative indicator light will turn off. Wash Cycle Adjustment Buttons To set a new wash cycle, follow the instructions contained in the paragraph entitled, "Setting and Starting a Wash Cycle. " 1/2 Load Button This button (see" Close-up View-Control Panel", letter "Q") makes it possible to wash dishes using only the upper rack if there are not enough dishes for a full load, This will allow you to save on If you forget to load some of the dishes. . . The wash cycle can be interrupted by opening the door carefully (in order to avoid being sprayed by hot water). When the door is closed again, the cycle will automatically restart at the point where it left off. water and electrical energy. It cannot be used with the heavy duty wash cycles. . 9. Salt GB Salt The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils. The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water. Adjusting Salt Consumption The dishwasher is designed to allow for adjusting the amount of salt consumed based on the hardness of the water used. [. . . ] If absolutely necessary, it can be positioned on its back. No solvents or Abrasive Cleaning Products To clean the exterior and rubber parts of the dishwasher, do not use solvents or abrasive cleaning products. Rather, use only a cloth and warm soapy water. To remove spots or stains from the surface of the interior, use a cloth dampened with water and a little while vinegar, or cleaning product made specifically for dishwashers. Seals One of the factors that cause odors to form in the dishwasher is food that remains trapped in the seals. Periodic cleaning with a damp sponge will prevent this from occurring. Cleaning and Special Maintenance Filter Assembly For best performance and results, the filter assembly must be cleaned frequently. [. . . ]