User manual HAIER L37V6-A8K

[. . . ] TFT-LCD COLOUR TELEVISION RECEIVER OWNER'S MANUAL This User's Manual is applicable for the following models: L26V6-A8, L26V6-A8K, L32V6-A8, L32V6-A8K, L37V6-A8, L37V6-A8K, L42V6-A8, L42V6-A8K, L32A9A, L32A9A-A, L32A1A, L32A1A-A Please READ this manual carefully before operating the unit, and keep it for future reference. *Please read this manual carefully before using your television and keep this manual in a good place for future reference. *To achieve the best performance of your television, read this User's Manual carefully and properly store it for future reference. *Information of screen displays and figures in the User's Manual may vary due to technical innovations. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Warning *To avoid electric hazards, it is strongly suggested that the back cover not be opened, as there is no any accessory inside the casing. *If necessary, please contact authorized after-sales services. [. . . ] Automatic mode is usually set as default. English-20 Other functions Position and phase adjust In YUV and D-SUB input mode, H-Position, Phase and Scope of pictures can be adjusted to eliminate transverse line interference and decentered picture as follows: When YUV/D-SUB input mode is set. Press Menu button on the remote controller and CH+/- for option of picture position adjust. The menu display is as follows: CH+ VOL- MENU VOL+ H-Position V-Position Phase A B C 50 50 50 CH- Picture Position Enter H-Position V-Position Phase Frequency A B C 50 50 50 50 Auto Adjust Picture Position Enter CH+ VOL- MENU VOL+ CH- 2. Press VOL+ button on television and remote controller to enter the menu of picture position setup. Press CH+/- button for desired adjust parameter option. Press VOL+/- for desired adjust parameter option until satisfactory value is achieved. When VGA signals are received, the automatic mode is used for parameter adjustment. (excluding HDTV 1080P, 1080i and 720P series) English-21 Other functions Timer setup If Off-time, On-time and Remind Time are intended in TV/AV1/AV2/S-Video/YUV/USB(USB only for the mo dels that have the function) , follow the instructions as below: 1. Press Menu button of television and remote controller, and the CH+/- button for timer setup menu. The menu display is as follows: CH+ VOL- MENU VOL+ Clock OFF Time ON Time ON Prog. A B C -- --- --- ----- --- -- CH- Remind Time Remind Prog. Timer Enter 2. Before activating timer setup, the clock must be correctly calibrated or otherwise the timer cannot be adjusted. If current time setting is cancelled, all previously set performance of the timer will also be inactivated. Note: The timer setup will not affect setup of the Sleep button and vice versa. Time setup: Press VOL+ button to set minute and VOL- to set hour. Program setup: Press VOL-/+ button for program number up and down. It is also possible to press digit buttons for program number option. Indication will appear on the screen 10 seconds prior to expiry of set time. Suppose off-time is set, and indication is as follows: OFF TIME 8S CH+ VOL- MENU VOL+ CH- Note: When the above indication appears on the screen, set time may be changed if VOL+/- button is pressed. English-22 Stream media playing system The USB port of some models receivers is connected with the storage device (Note 1) at USB interface for play of JPEG picture files, MP3 music files and some format movie files. If TV/AV button of television and remote controller is pressed, following menu will appear on the screen: 1. TV 2. AV1 3. AV2 4. SVideo 5. YUV 6. D-SUB 7. DVI 8. USB Press digit 8 button to swap to USB function interface (as shown in the figure below), or directly press the USB shortcut button for USB status swap. Then, connect USB storage device with the USB port. All the buttons for the interface functions are located at bottom of the remote controller as shown in the figure below: UP LEFT DOWN PREV. NEXT RIGHT PAUSE ENTER SWAP EXIT It is possible to press Up or Down button to select desired JPEG picture, MP3 music or movie, and to confirm the format of the media files (Note 2) to be read in the USB storage device. AAA Multimedia Player Pic & Music Movie Music Set up If USB includes two or more than two file system partitions (Note 3), press Right button to enter the partitions option mode (as shown in the figure below). Then press the Right button again to display all media files of relative formats under current partition and root directory, and all directory names of relative files included. English-23 Stream media playing system AAA Multimedia Player C D Most flash memories and memory cards have one partition. [. . . ] Link audio cable of a PC to AUDIO IN port of television. Press TV/AV button to select D-SUB mode. Turn on the PC and its screen picture will be displayed on the television screen. In this way, the television can be used as a PC monitor. D-SUB IN R L AUDIO IN DVI input Select digital RGB mode input for DVI input. [. . . ]