User manual HALCRO LOGIC SSP80

[. . . ] Owner's Manual SSP100 Surround Sound Processor SSP80 Surround Sound Processor www. halcro. com 1 Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Important Safety Information. . . . . . . . . . . . . . . . . . . 5 Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Electrical safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Protection from fluids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Service warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Use the SSP80/100 volume control (12) on the front panel (or UTSR1) to adjust the volume. Note: The SSP80/100 allows you to enter information about the size, distance and how many speakers you have in your system. To ensure you experience the best quality audio, refer to the speaker setup information on page 49. 46 47 Menu Structure > > SPEAKER SETUP Level setup Distance setup Size setup Aux channel setup Level Autocalibrate?EXIT Page 43 MAIN MENU Speaker setup Audio setup Source setup Display setup THX Audio setup Trigger setup EXIT Page 43 > DISPLAY SETUP Scaler setup TV system Superimpose Temporary disp. Video format Distance units OSD output OSD style EXIT NTSC Off Full Auto Feet Both Default Page 63 > AUDIO SETUP Dolby/DTS setup Preset setup Tone controls LFE level Reverb 0dB 2 > THX AUDIO SETUP Bass limiter setup Boundary gain comp No THX Ultra2 Sub Boundary gain comp ASA Back speakers EXIT > 1 SRC 1 HDMI No change HDMI 1 Off Page 57 Balanced source Off Balanced routing DSP EXIT > Page 51 Together Page 69 SOURCE SETUP Source Title Digital input Preset Analog monitor Video type Scaler bypass EXIT TRIGGER SETUP Trigger 1 sense PowerOn - polarity - delay - duration - polarity - delay - duration EXIT Posit No Infinit Posit No Default Page 73 Trigger 2 sense PowerOn 48 49 Speaker Setup It is important to set up the speaker system correctly to accurately recreate the recorded sound. MAIN MENU > Speaker setup Audio setup SPEAKER SETUP Source setup > Level setup Display setup Distance setup THX Audio setup Size setup Trigger setup Aux channel setup EXIT Level Autocalibrate?EXIT Note: `NONE' will be displayed if the speaker/ channel is not selected in the `Size Setup' menu, and the optional settings (Level, distance and so on) cannot be changed. To facilitate the speaker setup the SSP80/100 comes with a calibration microphone and tone generator (built in) that is used to automatically calibrate the sound levels coming from the speakers and setup their distances relative to the listening position. This setup can also be done manually. You can engage the noise calibration signal by pressing the TEST key on the UTSR1. This will start a test signal cycling through the channels. The test signal stays on the channel until no level change is done during the last few seconds. Pressing the TEST key again disengages the noise signal. Level auto calibration is recommended for setting the correct speaker levels, but if manual calibration is used, the correct sound pressure should be set to 75 dB using a hand held sound pressure meter set to `C' slow. This level corresponds to sound levels in public cinemas. To access the `Speaker setup' menu: o Enter the Main Menu. o Use the UP or DOWN keys until `Speaker Setup' is highlighted. o Press ENT to select. 50 Level setup Output channel levels are adjusted in Level setup. LEVEL SETUP > Left Center Right Right surround Right back Left back Left surround Subwoofer EXIT To set up output channel levels: o From the `Speaker Setup' menu, use the UP or DOWN keys to highlight `Level Setup' and press ENT. o Use the UP or DOWN keys to highlight the speaker/channel level you want to adjust. o Use the LEFT or RIGHT keys to adjust the level to your desired setting. o Repeat this process until you are happy with all level settings. o Use the UP or DOWN keys to highlight EXIT and press ENT to return to the `Speaker setup' menu 0. 0dB 0. 0dB 0. 0dB 0. 0dB 0. 0dB 0. 0dB 0. 0dB 0. 0dB DISTANCE SETUP > Left Center Right Right surround Right back Left back Left surround Subwoofer EXIT 6ft 5ft 6ft 3ft 0ft 0ft 3ft 0ft You can engage the noise calibration signal by pressing the TEST key on the UTSR1. This starts a test signal cycling through the channels. The test signal stays on the channel until no level change is made during the last few seconds. [. . . ] Proof of purchase options include: · · copy of sales receipt showing name of original owner, dealer, and purchase date copy of credit card voucher or cancelled check accompanied by owner's record of purchase date and serial number · Warranty registration While not required for service, we request that you register your Halcro product as soon as you purchase it. Please use the Halcro Product Warranty Registration form that is provided, or request a copy from your Halcro dealer. 89 Transportation of products Halcro pays freight one way to return product once warranty repair is completed. Halcro requests prepaid shipment to the factory or to a designated repair center or service agency. We are not equipped to accept freight collect shipments. [. . . ]