User manual HANNA INSTRUMENTS HI 99300

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual HANNA INSTRUMENTS HI 99300. We hope that this HANNA INSTRUMENTS HI 99300 user guide will be useful to you.

Lastmanuals help download the user guide HANNA INSTRUMENTS HI 99300.


Mode d'emploi HANNA INSTRUMENTS HI 99300
Download
Manual abstract: user guide HANNA INSTRUMENTS HI 99300

Detailed instructions for use are in the User's Guide.

[. . . ] WARRANTY All Hanna Instruments meters are warranted for two years against defects in workmanship and materials when used for their intended purpose and maintained according to instructions. The probes are warranted for six months. This warranty is limited to repair or replacement free of charge. [. . . ] If possible, use plastic beakers or containers to minimize any electromagnetic interference. · Select either EC or TDS mode (µS or ppm unit for HI 99300, mS or ppt unit for HI 99301) by pressing the SET/HOLD button. Temperature will always be displayed on the secondary LCD. · Tap the probe lightly on the bottom of the container to remove air bubbles that may be trapped inside the tip. · Allow a few minutes for the thermal equilibrium to be reached, i. e. until the instability symbol (on the top left corner of the LCD) disappears. · The meter will show the EC or TDS value automatically compensated for temperature and the temperature of the sample. · To freeze a reading on the LCD, press and hold the SET/HOLD button until "HOLd" appears on the secondary display. Press either button to return to normal mode. · To turn the meter OFF, press and hold the MODE button while in normal mode. "OFF" will appear on the LCD; release the button. CALIBRATION PROCEDURE · From EC measurement mode, press and hold the MODE button until "CAL" is displayed on the lower LCD. · Release the button and immerse the probe in the proper calibration solution (HI 7031 at 1413 µS/cm for HI 99300 or HI 7030 at 12. 88 mS/cm for HI 99301). · Once the calibration has been automatically performed, the LCD will display OK for 1 second and return to normal measurement mode. · The CAL symbol lights up on the LCD to indicate that the meter is calibrated. Note: Since there is a known relationship between the EC and TDS reading, it is not necessary to calibrate the meter in TDS. If the conversion factor is either 0. 5 or 0. 7, the meter will allow a direct calibration in TDS by using the Hanna calibration solutions. [. . . ] · Press the MODE button return to normal operation. BATTERY REPLACEMENT The meter displays the remaining battery percentage every time it is turned on. When the battery level is below 5%, the battery symbol lights up on the LCD to indicate a low battery condition. If the battery level is so low as to cause erroneous reading, the Battery Error Preventing System (BEPS) will automatically turn the meter off. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HANNA INSTRUMENTS HI 99300

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual HANNA INSTRUMENTS HI 99300 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag