User manual HANNA INSTRUMENTS HI 98811

[. . . ] Instruction Manual HI 98811 Fast Tracker Thermometer w w w. c o m Dear Customer, Thank you for choosing a Hanna Instruments Product. Please read this instruction manual carefully before using the instrument. This manual will provide you with all the necessary information for the correct use of the instrument, as well as a precise idea of its versatility in a wide range of applications. [. . . ] If the reading is out of range or the probe is not connected, the LCD will display a dashed line in place of the reading. Note: To choose between "°C " and "°F" unit, enter the setup code 70. After 1 year since last calibration the "DATE" symbol starts blinking on the LCD to warn the user that a recalibration is suggested in order to maintain a high accuracy of the meter. It is recommended that recalibration to be performed by authorized technical personnel only. Contact your nearest HANNA service center. 14 PRINTING/LOGGING FUNCTIONS Two different modes to print / log data are available: 1. Timed Logging; samples are stored and printed (if print function is active) at fixed time intervals. Log on Demand; samples are stored and printed (if print function is active) when the LOG key is pressed. It's possible to perform the Log on Demand either in normal mode or in Timed Logging mode. It is possible to switch from logging without printing to logging with printing in two ways: · set the function code 03 to "On" to enable printing, to "Off" to disable printing - while not in timed logging mode. · press ALT and PAPER to toggle between printer enabled and printer disabled while in Timed logging mode. TIMED LOGGING MODE To start Timed logging, press ALT and LOG. "tAG" will be displayed on the upper part of the LCD and "Id" on the lower part. For Sample ID code reading an i-Button® tag must be touched by the touch probe on the back of the meter within a 20 second interval. If a tag is recognized the meter will beep once and if the printing is disabled the last six digits of the tag's code will be displayed on the LCD for a few seconds. Tag reading can be skipped by pressing LOG (a null Sample ID will be stored). Note: Tag reading timeout - after 20 seconds left without reading any tag, the logging operation will be aborted with a longer beep. The lot number will be displayed for a few seconds, then the "LOG" "INTV" symbols will appear on LCD and if printer is enabled a first set of data will be printed. The "LOG" "INTV" symbols will be fixed if printer is enabled and will blink if printer is disabled. The printout provides the following #04 1m ID 2*3 3 5 4*2 information: 18/12/2004 17. 10 S. 0001 a - Lot number 24. 9°C b - Logging interval g 15 c - Sample ID (only for the first sample of the lot) d -Date (only for the first printed sample of the lot or of the day) e - Sample number f - Time g -Reading ("----" means out of range). If no keys are pressed, the meter enters sleep mode to prolong the battery life and only the "LOG" "INTV" symbols will be visible on LCD. While logging, during the sleep mode, the last logged reading will appear briefly on the LCD. To reactivate the LCD press ON/OFF. STOP LOGGING In order to stop the recording mode, press ALT and LOG (press ON/OFF first, if meter is in sleep mode). A last report containing the number of #04 1m logged samples (e. g. [. . . ] Eye-connector for mounting. 6. 4mm 0. 25" 406mm 16" EPOXY 19mm 0. 74" 9. 6mm 0. 38" 5. 5mm 0. 22" 1mm 0. 04" TIN PLATED Cu #6 STUD SIZE HI 76S2-4 NTC Thermistor sensor. Molded tip with epoxy seal for aggressive environments. 6. 4mm 0. 25" 406mm 16" 9. 6mm 0. 38" 2mm 0. 08" MOLDED TIP EPOXY FILLET Teflon® is registered Trademark of "du Pont de Nemours & Co. " 25 HI 76S2-5 NTC Thermistor sensor. Aluminum tab with mounting hole. 300mm 12" DIA 3mm 0. 12" EPOXY 8mm 0. 31" 1. 6mm 0. 06" 12. 7mm 0. 50" 6. 4mm 0. 25" 4. 7mm 0. 19" ALUMINUM HOUSING HI 76S2-6 NTC Thermistor sensor. PVC encapsulated tip for protection in aggressive environments. 6. 4mm 0. 25" 25. 4mm 1. 0" 300mm 12" 15. 8mm 0. 625" 7. 1mm 0. 28" MOLDED PVC TIP HI 76S2-7 NTC Thermistor sensor. [. . . ]