User manual HARMAN KARDON AVR 35

[. . . ] Harman Kardon AVR35 Audio/VideoReceiver Volume Speaker Channel Dig. Select Delay ITAL COAX AC-3 Set TUNING PRESET SCAN PRESET FM MODE DIGITAL PRO LOGIC 3-STEREO HALL 1 HALL 2 THEATER TEST TONE SURR. OFF Mute Bass Treble Balance VIDEO 3 Min Max Min Max L R Video L Audio R Owner's Manual Owner's Manual AVR35 Audio/Video Receiver Table of Contents Introduction. 4­6 Front Panel Information Display . [. . . ] Press the / / ¤ buttons h on the remote or the Selector buttons ¸ on the front panel until either LARGE or SMALL appears to match the type of speakers you have at the left front and right front positions, as described by the definitions shown below. When SMALL is selected, lowfrequency sounds will be sent to the subwoofer output only. Note that if you choose this option, and there is no subwoofer connected, you will not hear any low-frequency sounds from the front channels. System Configuration 18 When LARGE is selected, a fullrange output will be sent to the front left and right outputs, and NO low-frequency signals will be sent to the subwoofer output. When you have completed your selection for the front channel, press the Set button j ~, and then press the / / ¤ buttons h on the remote or the Selector buttons ¸ on the front panel to change the display to CEN SPEAKER. Press the Set button j ~ again, and use the / / ¤ buttons h on the remote, or the Selector buttons ¸ on the front panel, to select the option that best describes your system based on the speaker definitions shown above. When CEN SP SMALL is selected, low-frequency center-channel sounds will be sent to the subwoofer output only. Note that if you choose this option and there is no subwoofer connected, you will not hear any low-frequency sounds from the center-channel speaker. When CEN SP LARGE is selected, a full-range output will be sent to the center speaker output, and NO center-channel signal will be sent to the subwoofer output. When CEN SP NONE is selected, no signals will be sent to the centerchannel output. The receiver will operate in a "phantom" centerchannel mode and center-channel information will be sent to the leftand right-front-channel outputs. When you have completed your selection for the center channel, press the Set button j ~, and then press the / / ¤ buttons h on the remote or the Selector buttons ¸ on the front panel to change the display to SUR SPEAKER. Press the Set button j ~ again, and then use the / / ¤ buttons h on the remote or the Selector buttons ¸ on the front panel to select the option that best describes your system based on the speaker definitions shown above. When SUR SP SMALL is selected, low-frequency surround channel sounds will be sent to the subwoofer output only. Note that if you choose this option and there is no subwoofer connected, you will not hear any low-frequency sounds from the surround speaker. When SUR SP LARGE is selected, a full-range output will be sent to the surround-channel outputs, and NO surround-channel signals will be sent to the subwoofer output. When SUR SP NONE is selected, surround-sound information will be split between the front-left and frontright outputs. Note that for optimal performance when no surround speakers are in use, the Dolby 3 Stereo mode should be used instead of Dolby Pro Logic. When you have completed your selection for the surround channel, press the Set button j ~, and then press the / / ¤ buttons h on the remote or the Selector buttons ¸ on the front panel to change the display to S W SPEAKER. Press the Set button j ~, and then press the / / ¤ buttons h on the remote or the Selector buttons ¸ on the front panel to select the option that best describes your system. Select S-W SP ON if a subwoofer is connected to your system. Select S-W SP OFF if a subwoofer is NOT connected to your system. Note that when no subwoofer is selected, low-frequency sounds below 100Hz will be sent to the front left/right speakers, provided that the selection in step 4, above, has been set to LARGE. Otherwise, no low-frequency sounds will be heard. This option is not available when the front, center or surround speakers are set to SMALL. System Configuration 19 11. [. . . ] Press either the AVR b or the TV Device Control Selector c, depending on which system's volume control you wish to have attached for the punch-through mode. Note that the red light under the Device Control Selector will blink twice and then go out to confirm the data entry. Example: To have the AVR's volume control be activated even though the remote is set to control the TV, first press the TV Device Control Selector c and the Mute button ` at the same time. Next, press the Volume Up button followed by the AVR Device Control Selector b. Volume Punch-Through The AVR35's remote may be programmed to operate the Volume Controls from either the TV or the AVR to operate in NOTE: Should you wish to return the remote to the original configuration after entering a Volume Punch-Through, you will need to repeat the steps shown above. [. . . ]