User manual HARMAN KARDON AVR 85

[. . . ] Harman Kardon AVR85 Audio/VideoReceiver Volume L PCM ITAL O PRO·LOGIC 3·STEREO HALL MOVIE MATRIX RF OPT COAX MULTI NIGHT LFE P-SCAN TV DVD V1 V2 V3 TEST MEMO AUTO TUNED STEREO dB kHz MHz ATT DISP SLEEP MULTI OSD ATT MEMO CLR MODE P·SET P·SCN TUNE MUTE ode Bass Treble Balance VIDEO3 Min Max Min Max L R Video L Audio R Owner's Manual Staple or clip original invoice here. w Owner's Manual AVR85 Audio/Video Receiver Table of Contents Introduction . 4­5 Front Panel Information Display . 10­12 Installation, Setup and Configuration . [. . . ] The Night mode may also be turned on and off at any time by pressing the Night button e on the remote. When the Night mode is set, or to bypass this setting, press the ¤ button i to move to the next setting. The SETUP LOCK prevents any of the major control settings from being changed once it is engaged. This feature is set at the factory to UNLOCK, so that all settings may be adjusted. If you wish to prevent settings from being easily or inadvertently being changed, use the < or > buttons i on the remote until LOCK is highlighted. Once the LOCK setting is engaged and you exit SETUP MENU 3, no changes may be made to any of the Setup menus. To make changes to these menus you must return to SETUP MENU 3 and use the < or > buttons i on the remote until UNLOCK is highlighted. When the LOCK setting is engaged, the word LOCK will appear at the top of the menus to remind you that no changes may be made. At this point, unless you wish to make changes to the Multiroom system, press the ¤ button i twice and then press Select j to RETURN TO THE MAIN MENU. Setup and operation of the Multiroom system is described on page 32 of this manual. System Configuration 20 At this point you may wish to adjust the delay time settings, although it is best to use the factory settings for initial listening sessions. See the Advanced Features section later in this manual for information on delay settings. The remaining item to be adjusted before normal use of the AVR85 is adjustment of the output levels. Correct adjustment of these settings is critical to proper operation of the receiver in all surround modes, and particularly when Dolby Digital sources are being played. To set the output levels press the Select button j to call up the main menu (see figure #1)if it is not already on the screen, and then press the the ¤ button i until the on-screen cursor is pointing to TEST TONE. Press Select j to move to the TEST TONE menu. When you press Select you will immediately hear a test noise from the front right speaker. The on-screen display will change to a graphic representation of each of the speakers in your room, with one speaker position blinking (see figure #5). That speaker is the one whose level is being set. Note: This procedure will only operate if the AVR85 is in the PRO LOGIC, AC3, MOVIE or DOLBY 3 STEREO modes. If the test tone cannot be selected, check to see which surround mode is indicated in the front panel display. If it is not one of the modes mentioned above, select one of the correct modes using the Mode Selectors y, and then move the cursor to test tone to restart the procedure. While seated in the primary listening position, you should hear a test noise signal from the left front speaker. You may leave the volume setting where it is, or raise it to an appropriate level using the Speaker Adjust / or ¤ buttons n on the remote. [. . . ] To clear the entire system memory of the unit, press and hold the MEMO ^ and CLEAR & buttons until CLEAR MEMO appears in the front panel display. Release the buttons and note that the unit will turn off and then on. Remember that once you have cleared the memory in this fashion it will be necessary to re-establish all system configuration information and tuner presets. If the system is still operating incorrectly, there may have been an electrostatic discharge or severe AC line interference that has corrupted the memory or microprocessor. If a reset does not solve the problem, consult an authorized Harman Kardon service depot. Troubleshooting 35 Troubleshooting Guide SYMPTOM No front panel lights when power switch is pressed Display lights, but no sound or picture CAUSE · No AC Power SOLUTION · Make certain AC power cord is plugged into a live outlet. [. . . ]