User manual HARMAN KARDON AVR 360

[. . . ] AVR 460 AVR 360 AUDIO/VIDEO RECEIVERS OWNER'S MANUAL ­ Basic Functions SAFETY INFORMATION Important Safety InStructIonS 1. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ] Use Category 5/5e cable, as described in the instructions for your A-BUS components. The A-BUS system carries the audio signal to the remote components, while receiving IR control codes. A hub may distribute audio to many remote rooms. To control source devices exclusively from the remote A-BUS module, connect the AVR's Carrier Remote IR Output to a compatible IR input on the source. This avoids having conflicting control commands sent to a source intended for the A-BUS system. IR commands received from the A-BUS system are also distributed to the AVR's other IR outputs. Visit the Web site at www. harmankardon. com for information on available Harman Kardon hubs, the ABH 4 and ABH 4000, and amplified in-wall modules, the AB 1 and AB 2. Step eIGHt ­ Install a multizone System The AVR 460/AVR 360 offers several methods of distributing audio to other areas in your home, and it also features video distribution. IMPORTANT SAFETY NOTE: Installing a multizone system typically requires running cables inside walls. Always comply with the appropriate safety codes when installing concealed wiring. Failure to do so may present a safety hazard. If you have any doubt about your ability to work with electrical and telecommunications wiring, hire a licensed electrician or custom installer to install the multizone system. When the system is installed using method B or C below, multizone operation takes over the Surround Back/ Zone 2 amplifier channels, limiting the system in the main listening room to 5. 1 channels. Connect IR Control Devices to the Zone 2 IR Input For methods A, B and C, connect an IR control device to the Zone 2 IR Input for remote-room control of the multizone system, source devices and volume in the remote zone. An A-BUS system does not require a separate IR control connection. NOTE: Only analog audio sources are available to the multizone system. For digital sources, make a second, analog audio connection. The Bridge III source is available to the multizone system. Select one or all of these methods for audio distribution: A. Connect an external amplifier to the Zone 2 Audio Outputs (AVR 460 only). It is recommended that you place the amplifier in the same room as the AVR so that a shorter length of interconnect cable is used with a long run of speaker wire to the remote room. A long run of interconnect cable would be subject to signal degradation. Depending on your amplifier, distribute the audio signal to a single pair of speakers, or to several pairs placed in different rooms. The Zone 2 Audio Outputs offer the benefit of 7. 1-channel audio in the main room simultaneously with multizone operation. However, the benefit is achieved with the expense of an additional component, i. e. , the amplifier. [. . . ] This Advanced Functions Manual also contains more worksheets and the remote control function list. 36 TECHNICAL SPECIFICATIONS Audio Section Stereo Mode, Continuous Average Power (FTC) AVR 360: 70 Watts per channel, 20Hz - 20 kHz AVR 460: 75 Watts per channel, 20Hz - 20 kHz @ < 0. 07% THD, both channels driven into 8 ohms 7 Channel Surround Modes Power Per Individual Channel, with all channels driven Front L&R channels: AVR 360: 55 Watts per channel AVR 460: 60 Watts per channel @ < 0. 07% THD, 20Hz­20kHz into 8 ohms Center channel: AVR 360: 55 Watts AVR 460: 60 Watts @ < 0. 07% THD, 20Hz­20kHz into 8 ohms Surround (L & R Side, Back) channels: AVR 360: 55 Watts per channel AVR 460: 60 Watts per channel @ < 0. 07% THD, 20Hz­20kHz into 8 ohms AVR 360: 130 watts per channel into 6 ohms AVR 460: 140 watts per channel into 6 ohms @1kHz, <1% THD, one channel driven. Input Sensitivity/Impedance Linear (High-Level) Signal-to-Noise Ratio (IHF-A) 200mV/47k ohms 100dB Video Section Television Format Input Level/Impedance Output Level/Impedance Video Frequency Response (Composite) Video Frequency Response (Component Video) HDMITM PAL 1Vp-p/75 ohms 1Vp-p/75 ohms 10Hz­8MHz (­3dB) 10Hz­100MHz (­3dB) Version 1. 3a with 10-bit Deep Color ENGLISH 37 General Power Requirement Power Consumption AC 230-240V/50Hz AVR 360: Standby < 1W, 540W maximum AVR 460: Standby < 1W, 890W maximum (7 channels driven) Dimensions (Max) Width Height Depth Weight net 440mm 165mm 382mm AVR 360 : 13, 4 kg AVR 460 : 13, 5 kg Surround System Adjacent Channel Separation Analog Decoding 40dB (Pro Logic, etc. ) Dolby Digital (AC-3) 55dB DTS 55dB Frequency Response @ 1W (+0dB, ­3dB) High Instantaneous Current Capability (HCC) Transient Intermodulation Distortion (TIM) Rise Time Slew Rate 10Hz ­130kHz ±35 Amps Unmeasurable 16µsec 40V/µsec 87. 5­108. 0MHz IHF 1. 3µV/13. 2dBf Mono/Stereo 70/68dB (DIN) Mono/Stereo 0. 2/0. 3% 40dB @ 1kHz ±400kHz: 70dB 80dB 90dB 522­1710kHz 45dB Loop 500µV 1kHz, 50% Mod 0. 8% ±9kHz, 30dB Depth measurement includes knobs, buttons and terminal connections. Height measurement includes feet and chassis. Features, specifications and appearance are subject to change without notice. FM Tuner Section Frequency Range Usable Sensitivity Signal-to-Noise Ratio Distortion Stereo Separation Selectivity Image Rejection IF Rejection Harman Kardon and Logic 7 are trademarks of Harman International Industries, Incorporated, registered in the United States and/or other countries. [. . . ]