User manual HARMAN KARDON HD7300

[. . . ] a ­ (number in an oval) indicates a button or indicator on the remote. ¡ ­ (number in a circle) indicates a rear panel connection. 2 TABLE OF CONTENS Introduction Thank you for choosing Harman Kardon HD7300 CD player. The HD7300 is an exceptionally well-engineered product that offers high performance and ease of use. We ask that you take a few minutes to read through this Owner's Manual to familiarize yourself with the controls and functions. [. . . ] If the HD7300 is installed behind a cabinet or other obstruction that may block the path between the front-panel Remote Sensor 3 and the location of the remote, an optional external IR sensor may be used. Connect the sensor to the Remote IR-In Jack £ on the rear panel. This jack may also be connected to the IR-Output jack of another compatible Harman Kardon component or a compatible IRsystem- remote product. You may also use the IR Sensor in the HD7300 to send commands to other compatible remote controlled products. Connect the Remote IROut jack ¢ to the input of the other product or system. © Connect the power to a nonswitched AC wall outlet or to the accessory outlet on the rear of another audio device in your system and you are ready to go!NOTE: When using the accessory outlet on another product to power the HD7300 make certain that it has the compatibility to power a device that draws at least 14 watts of current in addition to being able to handle the requirements of the other devices that may be plugged into the accessory outlets. If you use a "switched" outlet, it is important to remember that the host product must be turned on in order for the HD7300 to operate. INSTALLATION 9 Operation Loading and Unloading Discs To load a disc, first turn the unit on (if not so already) by pressing the Power Switch 1 on the front panel or the Power On button 1 on the remote, then press the Open/Close button $ F taking care to make certain that the space in front of the drawer is not obstructed. Note that if the drawer is blocked when attempting to open it, it will automatically stop the motor for opening the tray after 10 seconds and an ERROR message will appear in the front display to protect the mechanism. When the unit is turned off (to Standby), pressing any button on the front panel will turn the unit on. When Play button 4 9 on the front or on the remote is pressed, the unit will automatically turn on and start playing the disc actually loaded. Load the disc in the tray with the printed (label) side facing up. The RANDOM indicator will light when that mode is in use. Random can be activated also while a track is playing. When Random is activated while programmed play is in use (see page 13), all programmed tracks will be played in random order. . You may also select a specific track by pressing the Skip buttons 7 7 until the wished track number is displayed (see page 12). The track may also be selected directly by entering the track number via the Numeric Controls 2, simply enter the track number by pressing the buttons that correspond to the desired track. Note that when a two-digit track number is being entered, the second digit of the number must be pressed within two seconds of the first digit. After the track is selected, press the Play button 4 9. Labeled Surface To retract the drawer back into the player after loading a disc, press the Open/Close button $ F. When the drawer is closed the display will indicate the total number of tracks on the disc and the total running time of the disc. The drawer will also close when the Play button 4 9 is pressed. The drawer will close and the disc will start playing the first track. 10 OPERATION Operation While the disc is playing, the track being played will show as a number in the middle of the display just below the word TRACK. The elapsed time of the track being played will also appear in the display (see figure page 10). [. . . ] Repeat All Tracks To repeat all of the tracks on a disc, press the Repeat button !5 until the REPEAT and ALL indicators light up. When you see these indicators, the entire disc or all programmed tracks will play through to the end, and then start again from the beginning. The disc will play continually until the Stop button 5 A is pressed. Repeat A­B The HD7300 may be programmed to repeat any section within a track, or a complete passage or program that includes material in a series of tracks. [. . . ]