User manual HARMAN KARDON STRATOPHONIC-SC4- OWNERS GUIDE

[. . . ] To fully enjoy the benefits of remote keypad control, please take a few minutes to read this owner's manual. It contains important information that will guide you through the correct and safe installation of your Amplified In-Wall Module. If you do not have experience installing in-wall electrical and telecommunications components, consult a qualified low-voltage contractor or custom installer. If you have any questions about this product, its installation or its operation, please contact your retailer or custom installer. [. . . ] The Bridge is a Harman Kardon accessory that is sold separately. It may be connected to a The Bridge-Ready Harman Kardon product. CD Source Control ­ When the STRATOPHONIC-SC4- is used with a Harman Kardon ABH 4000 or other compatible multizone A-BUS hub, and when a CD player is connected to Source 2 of the hub, tap this button to select the CD player as the source and begin play (if the player was not already playing). If audio is not heard within a few moments of the first tap, tap the button again, as the CD player may have already been playing and would have interpreted the command as a Pause. If this button was previously tapped to start play, press and hold the button to skip to the next disc (assuming the player is a multidisc unit). DVD Source Control ­ When the STRATOPHONIC-SC4- is used with a Harman Kardon ABH 4000 or other compatible multizone A-BUS hub, and when a DVD player is connected to Source 3 of the hub, tap this button to select the DVD player as the source and begin play. If this button was previously tapped to select the DVD player as the source, press and hold the button to begin play. MP3 Source Control ­ When the STRATOPHONIC-SC4- is used with a Harman Kardon ABH 4000 or other compatible multizone A-BUS hub, and when an MP3 player is connected to Source 4 of the hub, tap or press and hold this button to select the MP3 player as the source. Power Off/Mute ­ Tap this button to mute the STRATOPHONIC-SC4-. Muting the STRATOPHONIC-SC4- does not affect the source, which will continue playing. If the AVR's tuner or The Bridge is the current source, or if the STRATOPHONIC-SC4- is connected directly to the AVR, press and hold this button to turn off the AVR's multiroom system. Fully insert the wire into the connector, being certain to check the color codes of the pin assignments one last time. Carefully crimp the connector, making sure that each wire is securely fastened. Step Three: Connect the Category 5/5e cable to the STRATOPHONIC-SC4-. Once the wire is run to the remote location where the STRATOPHONIC-SC4- will be installed, connect the Category 5/5e cable to the STRATOPHONIC-SC4-. Prior to making the connections, strip the outer jacket of the Cat. Using the supplied mounting screws, attach the STRATOPHONIC-SC4- to the junction box or plaster ring through the Screw Slots. Attach a Decora-style wall plate (not included) through the STRATOPHONIC-SC4-'s Screw Holes. Although any color Decora wall plate may be used with the STRATOPHONIC-SC4-, the STRATOPHONIC-SC4- itself should not be painted. Selector Step Four: Connect the speaker cable to the STRATOPHONIC-SC4-. Connect speaker wires to the STRATOPHONIC-SC4- module using the colorcoded chart on the Speaker Terminal Block as a guide. Observe the positive (+) and negative (­) polarity indications, and avoid having the wire strands from one cable touch another. Loosen the retaining screws on the Speaker Terminal Block and insert the wire into the appropriate slots. [. . . ] · Wiring protocol: TIA wiring specification for T568A at the A-BUS-equipped product end. Connections at the STRATOPHONIC-SC4- are specified on the STRATOPHONIC-SC4-. · Connection terminals: IDC type for Category 5/5e cable; screw terminal type for speaker connections. · Speaker wire: Maximum AWG 14, in compliance with any applicable local building code or NEC requirements for in-wall, riser or plenum use. [. . . ]