User manual HARMAN KARDON TD202

[. . . ] Not all connectors shown will be present on all models. 2 AVR Connect Your Speakers How to use the AVR speaker terminals: Connections Connect Your Subwoofer Use a single RCA audio cable to connect the receiver's Subwoofer Pre-Out connector to your subwoofer. Consult your subwoofer's user manual for specific information about making connections to it. Receiver Subwoofer Connector Powered Subwoofer Single RCA Audio Cable (not supplied) 1. Tighten Cap Always connect the colored (+) terminal on the AVR to the (+) terminal on the speaker (usually red), and the black (­) terminal on the AVR to the (­) terminal on the speaker (usually black). IMPORTANT: Make sure the (+) and (­) bare wires do not touch each other or the other terminal. [. . . ] a Blu-ray DiscTM or DVD player; a cable, satellite or HDTV tuner; etc. Your receiver has several different types of input connectors for your audio and video source devices: HDMI, component video, composite video, optical digital audio, coaxial digital audio and analog audio. The connectors are not labeled for specific types of source devices; they are labeled numerically, so you can connect your devices according to your individual system's make-up. Your receiver's various source buttons have default assignments to different input connectors (listed in the "Default Source Button" column of the table below). For ease of setup, you should connect each source device to the connector where the corresponding default source button is assigned (e. g. , connect your Blu-ray Disc player to HDMI 1). Connections However, you can connect your source devices as you wish and reassign any of the source buttons to any of the input connectors listed in the table according to where you actually connect each of your source devices. As you connect your various source components, fill out the "Connected Component" column in the table ­ it will make it easier for you to assign the various source buttons after you have completed making all of the connections. (You will make any changes to the source-button assignments and fill in the "Assigned Source Button" column later in the setup process. ) AVR Input Connector HDMI 1 HDMI 2 HDMI 3 HDMI 4 HDMI 5 (AVR 3650, AVR 365 only) HDMI Front Component Video 1 Component Video 2 Composite Video 1 Composite Video 2 Optical Digital Audio 1 Optical Digital Audio 2 Coaxial Digital Audio Input 1 Coaxial Digital Audio Input 2 Analog Audio In 1 Analog Audio In 2 Analog Audio In 3 Connected Component Default Source Button Blu-ray Cable/Sat Game Media Server TV Aux A (red) B (green) C (yellow) D (green) A (red) B (green) C (yellow) Assigned Source Button D (green) Monitor Output Connector HDMI Monitor Out Composite Video Monitor Out Connected Component Record Output Connector Composite Video Rec Out Optical Digital Audio Out Connected Component Input Connections and Assigned Source Buttons 4 AVR HDMI Devices If any of your source devices have HDMI connectors, using them will provide the best possible video and audio performance quality. Since the HDMI cable carries both digital video and digital audio signals, you do not have to make any additional audio connections for source devices you connect via HDMI connectors. Note: If you have a TV or other source device equipped with the HDMI Audio Return Channel Function, you can feed its sound to the AVR via the HDMI Monitor Out connection's Audio Return Channel, and it will not require additional audio connections to the AVR. Refer to the complete AVR 3650, AVR 365, TD202, AVR 265 Owner's Manual, downloadable at www. harmankardon. com. Receiver HDMI Connectors Composite Video Cable (not supplied) Connections Composite Video Devices ENGLISH 5 Use composite video connectors for video source devices that don't have HDMI or component video connectors. You will also need to make an audio connection from the source device to the receiver. Receiver Video Connectors To Composite Video Output HDMI Cable (not supplied) Composite Video-Equipped Source Device Optical digital audio devices To HDMI Output If your non-HDMI source devices have optical digital outputs, connect them to the receiver's optical digital audio connectors. Use the remote's arrow and OK buttons to select "Speaker Setup. " Speaker Setup Automatic Setup ­ EzSet/EQ Automated Speaker Setup and EQ Manual Setup Manually Adjust Speaker Settings Configure Your Speakers 1. Plug the supplied EzSet/EQTM microphone into the receiver's Headphone connector. Receiver Headphone Connector 6. Select "Automatic Setup ­ EzSet/EQ. " 7. Follow the instructions that appear on the screens. Assign The Receiver's Source Buttons 1. Review the input connections you listed on the Input Connections and Assigned Source Buttons table, on page 4. Note what changes (if any) you want to make from the default source-button assignments that appear on the list. Turn on your TV and select the TV input where you connected the receiver in Connect Your TV, on page 3. EzSet Microphone (supplied) 8 AVR 3. Press the remote control's Setup button. The receiver's on-screen display (OSD) setup menu will appear on the TV. (Note: If you have used a composite video connection to your TV, the OSD menus will not appear on your TV. [. . . ] Select "Audio Input from Source" and select the audio input connector you want to assign to the source button. Press the remote control's Setup button again. The receiver's on-screen display (OSD) setup menu will reappear on the TV. (Note: If you have used a composite video connection to your TV, the OSD menus will not appear on your TV. [. . . ]