User manual HARMAN KARDON TU 970

[. . . ] TU 970 OWNER'S MANUAL Power for the Digital Revolution® Table of Contents 3 Introduction 4 Front Panel Controls 5 Rear Panel Connections 6 Remote Control Functions 7 Installation and Connections 8 Operation 8 8 9 9 9 9 10 11 Basic Operation Station List Preset Setting Function Control Station Order Signal Error Rate Preset Tune RDS Operation Declaration of Conformity We, Harman Consumer International 2, Route de Tours 72500 Château-du-Loir, FRANCE declare in own responsibility, that the product described in this owner's manual is in compliance with technical standards: EN 55013/6. 1990 EN 55020/12. 1994 EN 60065:1993 EN 61000-3-2/4. 1995 12 Troubleshooting Guide 13 Technical Specifications Carsten Olesen Harman Kardon Europe A/S 10/03 Typographical Conventions In order to help you use this manual with the remote control, front-panel controls and rear-panel connections, certain conventions have been used. EXAMPLE ­ (bold type) indicates a specific remote control or front-panel button, or rear-panel connection jack EXAMPLE ­ (OCR type) indicates a message that is visible on the front-panel information display 1 ­ (number in a square) indicates a specific front-panel control 0 ­ (number in a circle) indicates a rear-panel connection 0 ­ (number in an oval) indicates a button or indicator on the remote 2 TABLE OF CONTENTS Introduction Congratulations!With the purchase of the Harman Kardon TU 970 you are about to begin many years of listening enjoyment. While sophisticated systems are hard at work within the TU 970 to make all of this happen, hookup and operation are simple. [. . . ] If you select the station, the Information Display 7 will show STATION NOT AVAILABLE, and will go back to the current radio station. If no digital stations can be found, the display will show NO STATIONS AVAILABLE. You can now select MANUAL TUNE by pressing the Select Button !8 or turn the Control Ring ) to select AUTOTUNE FULL or AUTOTUNE LOCAL to try to manually find available stations. If no stations can be found, please check that the antenna is connected correctly and if your area is covered by DAB. 8 OPERATION Operation Preset Setting Besides having the TU 970 create a station list, you can also store presents into the tuners memory. Tune to the desired station with the Control Ring ). Press the Memory Button on the front panel 9 or on the remote control 9. You will see the 01 segments in the Information Display 7 will start to blink. Function Control The DAB mode in the TU 970 contains a menu structure to access various system options. To enter the menu, press the Function Button on the front panel 4 or on the remote control 6 once. To scroll through the list of sections of the menu, turn the Control Ring ) or press the Scroll Buttons on the remote control 5. The sections will be shown on the lower display line in the Information Display. To enter a section and see the options, press the Select Button Select button !8. You can scroll through the options with the Control Ring and activate an option by pressing the Select Button once that option is shown on the Information Display. Signal Error Rate In this section you can see the level of correction the TU 970 is applying to the DAB signal to maintain the audio quality. The level will be indicated by a numeric value between 0 (no correction) and 99 (maximum correction). For an acceptable quality, the value of 50 should not be exceeded. 3. Turn the Control Ring, until the desired station preset is shown in the Information Display. The desired preset can also be entered with the Numeric Keys on the remote control 1. Within 4 seconds, press the Memory Button again to store the station in the memory. Information settings The DAB signal contains besides the radio station additional information. This information can be made visible in the lower display line of the Information Display 7. The following information is available to display: 1. Dynamic Label Segment (DLS): scrolling text, supplied by the broadcaster. Program Type: describes the type of broadcast, e. g. Multiplex Name: will show the name of the multiplex of the broadcaster. [. . . ] When a station is tuned, the search will stop and the display will show the station's "Call Letters" or other "Program Service" information. To turn off the PTY Search at any time, press the RDS Button again. NOTE: Many stations do not transmit a specific PTY. The display will stay blank when such a station is selected and PTY is active. Processor Reset In the rare case where the unit's operation or the displays seem abnormal, the cause may involve the erratic operation of the system's memory or microprocessor. [. . . ]