User manual HASBRO MICRO MACHINES SUPER VAN CITY

[. . . ] Be sure to keep all operation manuals handy for reference including this manual, the "Operation manual (for general information and copier operation)" and operation manuals for any optional equipment which has been installed. (Option) Saddle stitch finisher + Punch module + Inserter + Large capacity tray The power switch positions are marked " I " to indicate power "ON" and " " to indicate stand-by. In the stand-by position, power is being supplied to a drying heater within the paper tray and sensor system in the printer. Caution: For complete electrical disconnection, pull out the main plug. The socket-outlet shall be installed near the equipment and shall be easily accessible. FOR YOUR RECORDS . . . [. . . ] The margin shift icon ( ) will also appear in the upper left of the screen to indicate that the function is turned on. SIDE 1 1/2 (0 1) inch 1/2 (0 1) inch SPECIAL MODES Use the and the keys to set the shift amount. The shift amount can be set from 0" to 1" in 1/8" (0 to 20 mm in 1 mm) increments. MARGIN SHIFT ERASE PAMPHLET COPY JOB BUILD 4 Touch the [OK] key on the special modes screen. You will return to the main screen of copy mode. About the steps that follow If an automatic document feeder is being used, see pages 4-7 through 4-10. If the document glass is being used, see pages 4-11 through 413. To cancel the margin shift function, touch the [CANCEL] key on the margin shift setting screen. 2 Select the shift direction. RIGHT LEFT Touch a shift direction key to select right or left. The selected key will be highlighted. 5-3 SPECIAL MODES Erase The erase function is used to erase the shadow lines on copies produced when copying thick originals or books. The erase modes that can be selected are shown below. The erase width is approximately 1/2" (10 mm) in it's initial setting. NOTE The initial setting for the erasure width can be changed in the key operator programs to any value from 0 to 1" (0 to 20 mm). (Page 14 of the Key operator's guide) Original Copy EDGE ERASE Eliminates shadow lines around the edges of copies caused when heavy paper or a book is used as an original. CENTER ERASE Eliminates shadow lines produced by the bindings of bound documents. EDGE + CENTER ERASE Eliminates shadow lines around the edges of copies and eliminates the shadow at the center of copies. To display the special modes screen. . . See "General procedure for using special functions" on page 5-2. 3 Adjust the amount of erase and touch the [OK] key. CANCEL EDGE OK 1 MODES Touch the [ERASE] key on the special modes screen. DUAL C TAN C 1/2 (0 1) inch Use the and keys to set the erase width to any value from 0" to 1" in increments of 1/8" (0 to 10 mm in 1 mm). RGIN SHIFT ERASE PHLET COPY JOB BUILD The erase setting screen will appear. The order of copying will be automatically adjusted by the machine. G Either left binding (right to left turning) or right binding (left to right turning) can be selected. G Four originals will be copied onto one sheet. Blank pages may be automatically produced at the end depending on the number of the originals. G If a saddle stitch finisher is installed, copies can be stapled in two positions along the center of copies and folded at the center. Right binding First page To display the special modes screen. . . See "General procedure for using special functions" on page 5-2. 3 Select the binding position (left binding or right binding). LEFT BINDING RIGHT BINDING C SE 1 Touch the [PAMPHLET COPY] key on the special modes screen. SPECI L MODES MARGIN SHIFT ERASE PAMPHLET COPY JOB BUILD The PAMPHLET COPY setting screen will appear. The pamphlet copy icon ( , etc. ) will also appear in the upper left corner of the screen to indicate that the function is turned on. If you wish to insert a different type of paper for use as a cover, follow steps 4 through 12 below. If you do not wish to insert paper for a cover, continue from step 8 on the next page. type of originals 2 Designate the or 2-sided. copied: 1-sided ORIGINAL 1-SIDED 2-SIDED to be 4 Touch the [COVER SETTING] key. CANCEL OK Select the [2-SIDED] key if you wish to scan a two-sided original using the automatic document feeding function. NG RIGHT BINDING COVER SETTING 5-6 SPECIAL MODES not you 5 Select whether oror "NO"). wish to copy on the cover ("YES" PRINT ON COVER YES NO the original in the document feeder 9 Place the document glass. (page 4-3) or on 10Ensure that the desired paper size has been automatically selected based on the original size. To select another size paper, select the desired size and touch the [AUTO IMAGE] key. The appropriate copy ratio will be selected 100% automatically based on the original size and the paper size. [. . . ] 7-6 to 7-12 -Filing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7 to 7-8 -Print jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9 -Quick file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6 -Scan save . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]