User manual HASBRO RISK-CASTLE RISK 1990

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following: · · · · Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit, different from that to which the receiver is connected. [. . . ] If the SSD provided in this kit is larger in capacity than the hard drive currently in your system, proceed to Handling Precautions. If the SSD provided in this kit is smaller in capacity than the hard drive currently in your system, please confirm that the used capacity on the system hard drive is not larger than the capacity of your new SSD. Perform the following steps to determine the Used Space on the system hard drive: 1) Boot your computer to your desktop. 2) Double click on My Computer (Computer in Vista) located on your desktop or via the Start Menu. 3) Single right-click on the C: drive and select Properties. The Properties window for the C: drive will appear (Figure 1): Figure 1: (C :) drive Properties If the used capacity is greater than the capacity of the SSD, it is required that you move some of your data such as pictures, movies, music, etc. off of the drive to an alternative data source (e. g. , external hard drive or USB drive) until the Used space is no more than 5 SSDNow For Desktops 85% of your new SSD capacity. This will help to ensure that the imaging process is successful. The following chart may be useful as a guide: SSD capacity 32GB 40GB 64GB 80GB 128GB 160GB 256GB 512GB Adjusted HDD Used Space 27GB or less 34GB or less 54GB or less 66GB or less 109GB or less 136GB or less 218GB or less 423GB or less Adjusted HDD Used space = SSD capacity X 85% After the cloning process has been successfully completed, these files can be moved back to their original location on the hard drive. Handling Precautions To prevent damage from static electricity, observe the following precautions: Allow the drive to remain in the anti-static container until you are ready to install the SSD. Wear a wrist strap and connect the ground strap to the computer case to minimize static electricity. Do not touch the connectors. Hardware Installation 1. Note: It may take a few minutes for the next screen to come into view. Figure 3: Acronis True Image HD 8 SSDNow For Desktops 5. Select Clone Disk from the Pick a Task screen (Figure 4). Figure 4: Pick a Task 6. screen will appear and the wizard will guide you through the cloning process (Figure 5). Click Next to continue. Figure 5: Disk Clone Wizard Note: If you receive an error message stating "This program is designed to work with two or more drives, " check all connections to both the hard drive and the SSD. Ensure that the SATA data and power cables are connected to the drives and motherboard. If all connections are in place, it is possible that your system 9 SSDNow For Desktops BIOS does not have the spare SATA ports turned on or enabled. If this is the case do the following: 1) Restart your computer. While the system is restarting, activate the system setup program (BIOS) by repeatedly pressing a special key such as ESC, F1, F12 or DELETE. (Consult your computer system's documentation for the correct key. ) 2) While in the system BIOS, look for an entry labeled "Drives or Hard Drives. " Select this field using the arrow keys on your keyboard and press Enter. Here, the spare SATA ports can be enabled or turned on by selecting the SATA port and changing the value to "On" or "Enabled". For best results, it is recommended that you enable or turn on all SATA ports during this process. [. . . ] If the new drive is larger than the original drive, the partitions will be enlarged proportionately. Figure 7: Hard Disk Drives Structure 9. Review the Acronis True Image HD operations to be performed (Figure 8). Click Proceed to begin cloning. Figure 8: Acronis True Image HD operations 10. An operation progress bar will indicate the data is being copied. [. . . ]