User manual HASBRO TRANSFORMERS GENERATION 2 DEVASTATOR

[. . . ]  The appliance must be installed by a qualified professional according to the instructions provided.  Any necessary adjustment or maintenance must be performed after the cooker has been disconnected from the electricity supply. Room ventilation The appliance may only be installed in permanentlyventilated rooms, according to current national legislation. The room in which the appliance is installed must be ventilated adequately so as to provide as much air as is needed by the normal gas combustion process (the flow of air must not be lower than 2 m3/h per kW of installed power). [. . . ] Adapting the grill Replacing the grill burner nozzle: 1. Remove the oven burner after loosening screw V (see figure). V TECHNICAL DATA Oven dimensions (HxWxD) Volume Useful measurements relating to the oven compartment Power supply voltage and frequency 34x38x44 cm 57 l width 42 cm depth 44 cm height 17 cm see data plate may be adapted for use with any type of gas shown on the data plate, which is located inside the flap or, after the oven compartment has been opened, on the left-hand wall inside the oven. Unscrew the grill burner nozzle using a special nozzle socket spanner (see figure) or preferably with a 7 mm socket spanner, and replace it with a new nozzle that is suited to the new type of gas (see Burner I and nozzle specifications table).  Be careful of the spark plug wires and the thermocouple tubes.  The oven and grill burners do not require primary air adjustment.  After adjusting the appliance so it may be used with a different type of gas, replace the old rating label with a new one that corresponds to the new type of gas (these labels are available from Authorised Technical Assistance Centres).  Should the gas pressure used be different (or vary slightly) from the recommended pressure, a suitable pressure regulator must be fitted to the inlet hose in accordance with current national regulations relating to “regulators for channelled gas”. = 37, 78 MJ/m³ 20 17 25 13 6, 5 18 C 34S G1 R /HA TRANSFORMERS GENERATION 2 DEVASTATOR R /HA 17 Descriptionof the appliance GB Overall view Gas burner Hob grid Control panel Containment surface for spills GUIDE RAILS for the sliding racks position 5 position 4 position 3 position 2 position 1 Adjustable foot GRILL DRIPPING PAN Adjustable foot Control panel OVEN control knob Hob BURNER control knobs OVEN LIGHT and ROTISSERIE button ANALOGUE TIMER knob* TIMER knob* OVEN control knob Hob BURNER control knobs OVEN LIGHT and ROTISSERIE button GAS BURNER ignition button* * Only available in certain models. 18 Start-up and use Using the hob Lighting the burners For each BURNER knob there is a complete ring showing the strength of the flame for the relevant burner. To light one of the burners on the hob: 1. Turn the TIMER knob in an anticlockwise direction # to set the desired length of time. Lower compartment* There is a compartment underneath the oven that may be used to store oven accessories or deep dishes. To open the door pull it downwards (see figure).  The internal surfaces of the compartment (where present) may become hot.  Do not place flammable materials in the lower oven compartment. In gas cooker models, there is a sliding protection layer A that shields the lower compartment from the heat generated by the burner (see figure). Place the rotisserie support in position 4 and insert the spit in the hole provided on the back panel of the oven. To remove the sliding protection remove the screw S (see figure). To replace it, lock it in place with the screw S. S  Before using the oven make sure that the sliding protection is fixed correctly. 20 Analogue timer* Setting the time Press the ANALOGUE TIMER knob and turn it in an anticlockwise direction to set the correct time. [. . . ] Inspecting the oven seals Check the door seals around the oven periodically. If the seals are damaged, please contact your nearest Authorised After-sales Service Centre. We recommend that the oven is not used until the seals have been replaced. GB Cleaning the appliance  Do not use abrasive or corrosive detergents such as stain removers, anti-rust products, powder detergents or sponges with abrasive surfaces: these may scratch the surface beyond repair. [. . . ]