User manual HASBRO VOCTRON

[. . . ] Please refer to the relevant laws in your Country. G No part of this publication may be reproduced, stored or transmitted in any form without prior permission from HASBRO ELECTRONICS (EUROPE) GmbH. SHOWVIEW is a registered trademark of Gemstar Development Corporation. The SHOWVIEW system is manufactured under license from Gemstar Development Corporation. [. . . ] Then press SET to confirm. GB-13 TINS-A083UMZZEnglish. book Page 14 Monday, November 11, 2002 9:39 AM BASIC OPERATION HOW TO SET A DELAYED RECORDING 8. Enter the start time using the [K/L] or the NUMBER BUTTONS hours first then minutes (when entering less than 10 minutes add a '0' before the number), for example for 21:05 start, press 2 1 0 5. Then press SET to confirm. DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D0 3 2 1 : 0 5 -:---/-- --:--:---/-- --:--:-1/2 SP * SP * ----- 9. Enter the stop time, for example for 22:30 stop, press 2 2 3 0. 10. If your VCR has long play facility and you wish to change the RECORDING SPEED, use the [H/J] to highlight SP. Press [K/L] to select standard play (SP), long play (LP) or extended play (EP) as required. DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D0 3 2 1 : 0 5 -:---/-- --:--:---/-- --:--:-1/2 SP * LP * ----- 11. For VPS/PDC setting use the [H/J] to highlight the final column. Using the [K/L] will select VPS/PDC ON or OFF ( * = ON - = OFF). 12. Press SET to confirm. · The MENU now shows all the timer settings you have entered. If you wish to make additional timer recordings, repeat this procedure. 1/2 DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7 D 0 3 2 1 : 0 5 22 : 3 0 --/-- --:--:---/-- --:--:-SP * LP ----- 13. When you have completed entering timer settings, press MENU to remove the menu from the TV screen. 14. The RIGHT audio channel will be sent to BOTH speakers. The MONO track will be sent to BOTH speakers. L and R will disappear from the VCR display. Pressing AUDIO OUT a fourth time, normal Hi-Fi stereo sound will be heard. L and R will appear on the VCR display. IGR Hi-Fi STEREO SOUND Your VCR can receive and record IGR sound. The VCR is normally set so that IGR sound is possible if it is present on the receiving signal, otherwise the VCR will automatically switch to receive the mono signal. NOTES: · · · · If the tape being played back does not carry sound recorded on Hi-Fi tracks, L and R will not appear on the display. lf the sound contains `crackling' or `popping' noises the sound quality may be improved by adjusting the tracking using CHANNEL K/L . If the poor quality is for a long period the VCR will automatically select the mono track and the sound will be in mono. Not all TV transmitters provide IGR sound. In this case the VCR automatically switches to receive the mono signal. GB-16 TINS-A083UMZZEnglish. book Page 17 Monday, November 11, 2002 9:39 AM ADVANCED OPERATION AUDIO AND YOUR VCR CONNECTING TO AUDIO EQUIPMENT The diagram below shows how to connect your VCR to audio equipment. When connected in this way stereo sound is possible from the speakers. EXISTING AERIAL CABLE BACK OF TELEVISION RF CONNECTION CABLE LINE1(I)IN /OUT SON/VIDEO (L1/I) AERIAL IN ENTREE ANTENNE LINE2(II)IN/DECODER CANAL PLUS/L2(II) AUDIO OUT SORTIE SON AERIAL OUT SORTIE ANTENNE AERIAL IN AA013 RD LG AERIAL OUT AUDIO OUT L and R AUDIO PHONO LEADS (NOT SUPPLIED) + AMPLIFIER GB-17 TINS-A083UMZZEnglish. book Page 18 Monday, November 11, 2002 9:39 AM ADVANCED OPERATION PLAYBACK OF A VIDEO TAPE CHECKING THE AMOUNT OF TAPE REMAINING When you load a video tape into the VCR it can calculate approximately the amount of video tape remaining in hours and minutes. [. . . ] · Batteries have not been inserted correctly. · VCR is positioned in strong light. · Make sure there is no other tape in the VCR. · Make sure you are loading the tape correctly. [. . . ]