User manual HASBRO WEEBLES BUSY FIRE STATION RIDE-ON

[. . . ] Ez a berendezés megfelel az 1999/5/EK Irányelvnek. Ta oprema je v skladu z zahtevami Direktive 1999/5/EC. Seade vastab direktiivi 1999/5/EÜ nuetele. Si ierice atbilst tehniskam prasibam pec 1999/5/EC direktivas. [. . . ] mode, your fax will automatically receive voice and fax messages if you have connected an answering machine to the fax machine. See Chapter 6 for more details. Using FAX Mode Changing the number of rings If desired, you can change the number of rings on which the fax machine answers incoming calls in FAX and TEL/FAX mode. Any number from 2 to 5 can be selected. 1 2 3 Display: Press once and 4 once. OPTION SETTING Press once. NUMBER OF RINGS Enter the desired number of rings (any number from 2 to 5). Example: 3 rings 3 4 Press to return to the date and time display. 42 Using TEL Mode Using TEL Mode When the reception mode is set to TEL, you must answer all calls by picking up the fax machine's handset or an extension phone connected to the same line. To select TEL mode, press , 1 , and 1. 10-MAY 10:35 TEL Answering with the fax's handset 1 When the fax machine rings, pick up the handset. 2 If you hear a fax tone, wait until the display shows RECEIVING and then replace the handset. Beep RECEIVING Note: If you have set the Fax Signal Receive setting (page 45) to NO, press to begin reception. 3 If the other party first speaks with you and then wants to send a fax, press after speaking. (Press before the sender presses their Start key. ) RECEIVING · When RECEIVING appears in the display, hang up. 43 3. Receiving Faxes Using TEL Mode Answering on an extension phone 1 Answer the extension phone when it rings. 2 If you hear a soft fax tone, wait until your fax responds (the extension phone will go dead), then hang up. Beep Phone goes dead 3 If the fax doesn't respond, or if the other party first talks to you and then wants to send a fax, press twice on the extension 5 once and phone (only on a tone dial phone). This signals the fax to begin reception. Hang up. · The above step is necessary if you have set the Fax Signal Receive setting (page 45) to NO. · Your fax will not accept the signal to begin reception (5**) if a document is loaded in its feeder. 44 Optional Reception Settings Optional Reception Settings Fax Signal Receive Your fax will automatically begin reception if you hear a soft fax tone after answering a call on your fax or an extension phone. If you use a computer fax modem to send documents on the same line, you must turn this function off in order to prevent your fax from mistakenly attempting to receive documents from the computer fax modem. Follow the steps below to change the setting. Display: 1 2 3 Press once and 4 once. OPTION SETTING Press 3 times. FAX SIGNAL RX Press 1 to turn on the function, or 2 to turn it off. 4 Press to return to the date and time display. 45 3. Receiving Faxes Substitute Reception to Memory Changing the number for remote fax activation If desired, you can use a number other than 5 to activate fax reception from an extension telephone. SET socket. 2 Connect the answering machine's telephone line plug to the TEL. NE To answering machine's telephone line socket. 50 Using the Answering Machine Connection Changing the outgoing message The outgoing message (OGM) of your answering machine should be changed to inform callers who want to send a fax to press their Start key. For example, your message might go as follows: "Hello. No one is available to take your call right now. Please leave a message after the beep or press your facsimile Start key to send a fax. Thank you for calling. " It is advisable to keep the length of the message under 10 seconds. If it is too long, you may have difficulty receiving faxes sent by automatic dialling. If your outgoing message must be longer than 10 seconds, leave a pause of about four seconds at the beginning of the message. This will give your fax a chance to detect fax tones sent when automatic dialling is used. Using the Answering Machine Connection 1 Press 1 , and 4 to set the reception mode to A. M. , 10-MAY 10:35 2 Set your answering machine to auto answer. Your answering machine must be set to answer on a maximum of two rings. If not, you may not be able to receive faxes sent by automatic dialling. If your answering machine has a toll saver function, make sure that it will answer by the fourth ring. Note: If your answering machine has a remote retrieval function, make sure the code used to activate remote retrieval is different from the code used to activate fax reception with an extension telephone (see Chapter 3, Receiving Faxes). If they are the same, entering the code from an outside telephone to retrieve messages will cause the fax machine to be activated. 51 6. Answering Machine Using the Answering Machine Connection How answering machine mode operates While you are out, all of your incoming calls will be answered by your answering machine and its outgoing message will play. During this time, your fax will quietly monitor the line. [. . . ] Your fax machine will automatically reattempt the call. (See Automatic redialling on page 39. ) RECALLING 79 10. This may occur during fax reception if too much data is received before the pages can be printed out. If faxes have been received to memory because printing is not possible, resolve the problem so that printing can continue. [. . . ]