User manual HASBRO XRC SKYDRIVER

[. . . ] NÄR DENNA DEL ÄR ÖPPNAD OCH UND VORSICHT UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNETAUSSETZEN. VARNING OSYNLIG LASERSTRÅLNING FARLIG. STRÅLEN ÄR SICHERHEITSVERRIEGELUNG ÜBERERÜCKT. NICHT DEM STRAHL OHITETTAESSA LASERSTRÅLING ADVARSEL USYNLIGFUNKTION. [. . . ] When the copy job ends, press the clear ( ) key twice, or press the ON LINE key once to change the unit to the online state (p. 32), or wait until the set auto clear time (p. 53) elapses. The remaining print data will be sent to the unit and printing will resume. Interrupt copying is not possible during a print job using the single bypass. ORIGINAL PLACEMENT Using the original table · The original table can read up to A4 (8-1/2" x 14") original. · Image loss 4mm (5/32") can occur at the leading and trailing edges of the copies. Also image loss 4. 5mm (11/64") in total can occur along the other edges of the copies. · When copying a book or an original which has been folded or a crumpled original, press down the original cover lightly. If the original cover is not securely closed, the copies may be striped or blurred. 5 1 2 Open the original cover/SPF, and place the original. Place an original face down on the original table. Align it with the original scale and the centring ( ) mark. Gently close the original cover/SPF. Original scale mark 47 Setting a large original (AL-1217) The original cover can be removed to allow copying of bulky objects. 1 Simply lift the original cover straight up. 2 To reattach the original cover, reverse the above procedure. Using the SPF The SPF is designed to hold up to 30 originals measuring from A5 to A4 (5-1/2" x 81/2" to 8-1/2" x 14") and weighting from 52g/m2 to 90g/m2 (14 lbs. · Before feeding originals in the original feeder tray, be sure to remove any staples or paper clips from them. (p. 53) ) mode can be 1 Press the exposure mode selector key to select the MANUAL ( ) mode or PHOTO ( ) mode. 2 Use the light ( ) and dark ( ) keys to adjust the exposure level. If exposure level 2 is selected, the two left-handmost indicators for that level will light up simultaneously. Also, if level 4 is selected, the two right-handmost indicators for that level will light up simultaneously. 49 Automatic exposure adjustment This automatic exposure level will remain in effect until you change it again by this procedure. The automatic exposure level can be adjusted to suit your copying needs. This level is set for copying from the original table and copying from the SPF respectively. 1 When adjusting the automatic exposure level for copying from the SPF, place an original in the original feeder tray and make sure that the SPF ( ) indicator lights up. When adjusting the level for copying from the original table, make sure that no original is left in the original feeder tray. Press the exposure mode selector key to select the PHOTO ( ) mode. 2 3 Press and hold down the exposure mode selector key for approximately 5 seconds. The PHOTO ( ) indicator will go out and the AUTO indicator will begin to blink. One or two light and dark indicators corresponding to the automatic exposure level which has been selected will light up. Press the light ( ) or dark ( ) key to lighten or darken the automatic exposure level as desired. If exposure level 2 is selected, the two left-handmost indicators for that level will light up simultaneously. [. . . ] Export Law Assurances. You agree and certify that neither the Software nor any other technical data received from HASBRO, nor the direct product thereof, will be exported outside the United States except as authorized and as permitted by the laws and regulations of the United States. If the Software has been rightfully obtained by you outside of the United States, you agree that you will not re-export the Software nor any other technical data received from HASBRO, nor the direct product thereof, except as permitted by the laws and regulations of the United States and the laws and the regulation of the jurisdiction in which you obtained the Software. 5. Government End Users. If you are acquiring the Software on behalf of any unit or agency of the United States Government, the following provisions apply. The Government agrees: (i) if the Software is supplied to the Department of Defense (DoD), the Software is classified as "Commercial Computer Software" and the Government is acquiring only "restricted rights" in the Software and its documentation as that term is defined in Clause 252. 227-7013 (c)(1) of the DFARS; and (ii) if the Software is supplied to any unit or agency of the United States Government other than DoD, the Government's rights in the Software and its documentation will be as defined in Clause 52. 22719 (c)(2) of the FAR or, in the case of NASA, in Clause 18-52. 227-86 (d) of the NASA Supplement to the FAR. 73 6. [. . . ]