User manual HASBRO YAHTZEE DELUXE EDITION IN ENGLISH AND SPANISH

[. . . ] Do not install the copier in a humid or dusty location. When the copier is not used for a long time, for example, during prolonged holidays, turn the power switch off and remove the power cord from the outlet. When moving the copier, be sure to turn the power switch off and remove the power cord from the outlet. Do not cover the copier with a dust cover, cloth or plastic film while the power is on. [. . . ] Enables or disables the automatic tray switching which occurs when paper in a tray runs out. (This switching cannot switch to the bypass tray. ) Enables or disables the auditing mode, which controls access to copier. Changes account numbers for auditing mode. Displays the total number of copies made against account numbers. Resets all audit accounts or resets any desired individual account. Sets the amount of the edge erase and centre erase areas. Enables or disables the offset function of the paper output tray. The offset function can be specified respectively for the upper and lower areas separated by an optional job separator tray kit. (AR-161 only) 7 8 GENERAL INFORMATION User programs 9 10 11 12 13 14 15 16 17 18 19 * These programs do not affect the copier functions unless certain optional equipment is installed. 36 USER PROGRAMS Setting the user programs 1 Press and hold the light ( ) key for more than 5 seconds until all the alarm indicators ( , , , , and ) blink and "­ ­" appears in the copy quantity display. 2 Enter a program number using the numeric keys. q q The selected program number will blink in the copy quantity display. If a mistake is made in steps 2 to 4, press the CLEAR ( copier will return to step 2. The program numbers are shown in the table below. 11 is entered, "­­­" will blink in the copy quantity display. q If the number of accounts has reached the upper limit (20), "11E" will appear in the copy quantity display. The copier will return to step 2 on page 37. User programs 1. Enter a 3-digit account number using the numeric keys. q Any 3-digit number except "000" can be registered as an account number. 2. Press the START key. q If a number that is already registered or "000" is entered, the number will blink in the copy quantity display. 3. 4. Repeat steps 1 and 2 for other account numbers. To continue with other user programs, press the key and enter another program number. To exit the user program mode, press the light ( ) key. 39 USER PROGRAMS Program No. 12 is entered, an account number will appear in the copy quantity display. q If no account number has been registered, "12E" will appear in the copy quantity display. The copier will return to step 2 on page 37. 1. Use the copy ratio display ( number to be changed. q ) key to select the account Use the key to advance through the account numbers. 2. Press the START key. q The account number will be erased and "­­­" will blink in the copy quantity display. 3. 4. Enter a new account number using the numeric keys. Press the START key. q If a number that is already registered or "000" is entered, the number will blink in the copy quantity display. 5. [. . . ] Eye; In case of contact, immediately flush eyes with water for 15 minutes. Route(s) of Entry: APPENDIX 75 Section 6. Physical Chemical Characteristics Not applicable Not applicable Not applicable Not applicable Fine powder Odorless Specific Gravity: Solubility in Water: PH: Viscosity: Color: about 7. 3 Negligible Not applicable Not applicable Black Boiling / Melting Point: Vapor Pressure: Vapor Density: Evaporation Rate: Appearance: Odor: Section 7. Fire and Explosion Data Not applicable >350°C (LEL); Not applicable (UEL); Not applicable CO2, dry chemical, foam or water None This material has no unusual fire or explosion hazards. None None Flash Point (Method Used): Ignition Temperature: Flammable Limits: Extinguishing Media: Special Fire Fighting Procedure: Unusual Fire and Explosion Hazard: Sensitivity to Mechanical Impact: Sensitivity to Static Charge: Section 8. Reactivity Data Stable None CO and NOx Will not occur. Stability: Incompatibility (Material to Avoid): Hazardous Decomposition: Hazardous Polymerization: Section 9. Precautions for Safe Handling and Use Personal Protection Information (Respiratory, Eye Protection and Protective Glove): None required under normal use. Engineering Control / Ventilation: Not required. Steps to be taken in case of Spill or Leak: Sweep up or clean up with vacuum cleaner. [. . . ]