User manual HASBRO ZOIDS LIGHTNING SAIX 83162

[. . . ] If your copier is so marked, please read "I" for "ON" and " " for "OFF". For a complete electrical disconnection, pull out the main plug. The socket-outlet shall be installed near the equipment and shall be easily accessible. This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/68/EWG. [. . . ] · You can also select a program by directly entering the program number with the numeric keys. USER PROGRAM 2:PREHEAT MODE 1, 2, 3, 1, 2, 3, SP. FUNC 3 Press the [ ] key ( ) or [ ] key ( ) to change the setting of the selected item. See "USER PROGRAM" (p. 64 to p. 68) for the program code. PREHEAT MODE 1:30 SEC 1, 2, 3, 1, 2, 3, SP. FUNC Note · If you mistakenly select the wrong item, press the [CLEAR] key ( ) and repeat the procedure from step 2. · To cancel a setting for a user program, press the [MENU] key. 4 Press the [OK] key. Your selection appears briefly and then the previous screen appears. Note When "AE LEVEL ADJUST" is selected in the user programs and the [OK] key is pressed, the automatic exposure adjustment screen appears. Adjust the exposure and press the [OK] key 7 69 USER SETTINGS Audible signals (key entry beep, invalid key beep, base setting beep) The machine sounds three different types of beep signals: a key entry beep that sounds when a valid key is pressed, an invalid key beep that sounds when an invalid key is pressed, and a base setting beep that sounds when a setting is the same as the base setting (base settings are explained below). The base setting beep is initially disabled. If you wish to enable the base setting beep, see "SOUND AT DEFAULT" on page 67. If you wish to change the volume of the beep signals or disable them, see "KEY TOUCH SOUND" on page 66. The beep patterns of each type of beep signal are as follows: Key entry beep. . . . . . . . . . . . . . . . . . . . . One beep Invalid key beep. . . . . . . . . . . . . . . . . Three beeps Base settings The base settings are preset standard selections for each copy setting. Press the [MODE SELECT] key to switch to printer mode and follow the instructions in the display. ("XX" indicates paper size) An original remains on the document glass, or the original is too thick to scan. If the message is no cleared when there is no original on the document glass, the underside of the RSPF is dirty. Clean the underside of the RSPF (especially areas where black lines appear. ) Printing is not possible if the paper size setting is different from the size of paper loaded in the tray. Load the same size of paper as the paper size setting and then press the [START] key ( ). ("XX" indicates paper size) The machine is not correctly connected to the computer. Check the cable (when using the scanner function). Page 86 85 86 34 TD CARTRIDGE IS NEAR EMPTY. Steadily A DRUM lit CARTRIDGE WILL BE NEEDED SOON. NO 2-SIDED COPY FROM BYPASS TRAY. NO 2IN1 COPY FROM BYPASS TRAY. INSTALL A TD CARTRIDGE. 30 35 35 38 29 35 64 85 NO XX SIZE TRAY - 24 CHECK SPF/RSPF. START TO RESUME. 88 LOAD XX PAPER INTO TRAY. 19 NO PC COMMUNICATION; CHECK CABLE. 46 47 72 TROUBLESHOOTING THE MACHINE The following problems are related to the general operation of the machine and copying. [. . . ] 37 Automatic two-sided copying - Document glass. . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 - RSPF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Margin shift, using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Sort copying, using - Document glass. . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]