User manual HATCO MNM-0702

[. . . ] MACHO NACHO Chip Warmer TM FDW-1-MN & FST-1-MN Series Installation & Operating Manual I&W #07. 05. 087. 00 HOLDING AND DISPLAY CABINET FLAV-R-SAVOR This manual contains important safety information concerning the maintenance, use and operation of this product. Failure to follow the instructions contained in this manual may result in serious injury. If you are unable to understand the contents of this manual, please bring it to the attention of your supervisor. Do not operate this equipment unless you have read and understood the contents of this manual. Este manual contiene importante información sobre seguridad concerniente al mantenimiento, uso y operación de este producto. [. . . ] WARNING To prevent any injury, discontinue use if power cord is frayed or worn. NEMA 5-15P BS-1363 CEE 7/7 Schuko Figure 3. Plug Configurations ELECTRICAL RATING CHART Model FDW-1-MN Voltage 100 120 220 240 220-230 (CE) 230-240 (CE) 120 220 240 220-230 (CE) 230-240 (CE) Hertz 60 60 50/60 50/60 50/60 50/60 60 50/60 50/60 50/60 50/60 Watts 1110 1128 1118 1128 1118-1222 1036-1128 1245 1225 1245 1219-1332 1150-1252 Amps 11. 1 9. 4 5. 1 4. 7 5. 1-5. 3 4. 5-5. 7 10. 4 5. 6 5. 2 5. 6-5. 8 5. 0-5. 2 Plug Configuration NEMA 5-15P NEMA 5-15P CEE 7/7 Schuko BS-1363 CEE 7/7 Schuko BS-1363 NEMA 5-15P CEE 7/7 Schuko BS-1363 CEE 7/7 Schuko BS-1363 Shipping Weight 80 lbs. (60 kg) FST-1-MN DIMENSIONS Model FDW-1-MN FST-1-MN Width (A) 18" (46 cm) 22-7/8" (58 cm) Depth (B) 22-3/8" (57 cm) 27" (69 cm) Height (C) 27-1/2" (70 cm) 32-5/8" (83 cm) A B Figure 4. MNM-0702 INSTALLATION SET-UP The Macho NachoTM unit comes pre-assembled and ready for set-up. Remove tape and protective film from all surfaces of unit. Install the chip deflector inside, behind the upper door. Install decals on the upper front and side stainless steel panels. Before installing decals, clean the stainless steel side panels with a non-oily cleaner, such as isopropyl alcohol (rubbing alcohol). After the cleaned surfaces have dried, simply remove the protective backing from the decal and apply to the panel. Any air pockets or bubbles behind the decal can be removed by rubbing gently with a soft cloth, working from the center of the decal towards the outer edges. WARNING For safe and proper operation, the unit must be located at a reasonable distance from combustible walls and materials. If safe distances are not maintained, discoloration or combustion could occur. CAUTION To prevent injury or damage the unit must be transported in the upright position. If laid on its side, all glass surfaces must be secured with tape. CAUTION Locate the unit at the proper counter height, in an area that is convenient for use. The location should be level to prevent the unit or its contents from accidentally falling, and strong enough to support the weight of the unit and food displayed. For safe and proper operation locate the unit indoors where the ambient air temperature is a minimum of 70°F (21°C). Chip Deflector Install chip deflector in slots located behind upper door panel. Floor Panels Decal-Install on upper stainless steel panel. Figure 5. MNM-0702 4 OPERATION ALL MODELS CAUTION Some exterior surfaces on the unit will get hot. Use caution when touching these areas to avoid injury. Plug warmer into a properly grounded electrical outlet of the correct voltage, size and plug configuration. Turn the Power Switch to the ON position. Turn the Temperature Control to the desired temperature setting. [. . . ] Pompano Beach 954-971-0456 650-635-1900 Electrical Appl. Repair Service Independence 216-459-8700 E. Oklahoma City 405-235-2184 Krueger, Inc. Oklahoma City OREGON Bressie Electric Co. [. . . ]