User manual HATCO PMGH-60M-0405(1)

[. . . ] QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ: · Ne pas tenter d'allumer d'appareil. · Ne touchez à aucun interrupteur; ne pas vous servir des téléphones se trouvant dans le bâtiment. · Appelez immediatement votre fournisseur de gaz depuis un voisin. · Si vous ne pouvez rejoindre le fournisseur, appelez le service des incendies. [. . . ] WARNING The flow of air to the heater for combustion and ventilation must not be obstructed. Air vents on the bottom and side of the unit should never be blocked. This unit is designed to vent directly into the room and is intended for commercial food service water heating only. WARNING Flue gases exit top sides of this unit and must not be obstructed, specified clearances must be maintained for safe operation. EXCERPT FROM ANSIZ223. 1/NFPA #54 7. 2. 1 Connection To Venting Systems. Excerpt as permitted in 7. 2. 2 through 7. 2. 6, all gas utilization equipment shall be connected to venting systems. 7. 2. 2 Equipment Not Required To Be Vented. A single booster-type [automatic instantaneous] water heater, when designed and used solely for the sanitizing rinse requirements of a dishwashing machine, provided that the equipment is installed, with the draft hood in place and unaltered, if a draft hood is required in a commercial kitchen having a mechanical exhaust system. Where installed in this manner, the draft hood shall not be less than 36 inches (914 mm) vertically and 6 inches (152 mm) horizontally from any surface other than the equipment. Where any or all of this equipment is installed so the aggregate input rating exceeds 20 Btu per hour per cubic foot (207 watts per m3) of room space in which it is installed, one or more shall be provided with venting systems or other approved means for removing the vent gases to the outside atmosphere so the aggregate input rating of the remaining unvented equipment does not exceed the 20 Btu per hour per cubic foot (207 watts per m3) figure. Where the room or space in which the equipment is installed is directly connected to another room or space by a doorway, archway or other opening of comparable size that cannot be closed, the volume of adjacent room or space shall be permitted to be included in the calculation. National Fuel Gas Code COMPONENTS The Hatco Gas Booster Heater Exhaust Hood operates on 120 VAC, 60 Hz, 15 amp, single phase service. All internal electrical connections have been made at the factory. WARNING If an external electrical source is utilized, the appliance, when installed, must be electrically grounded in accordance with local codes, or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, CSA C22. 1, Electrical Code. ELECTRICAL CONNECTIONS To connect the field wiring to the booster hood: 1. Remove the exhaust outlet cover to expose the wiring compartment. Connect the power supply leads to the pigtails provided. PMGH-60M-0405 MAINTENANCE GENERAL Inspect the fan monthly to make sure it is operating freely and is free of lint and dirt. WARNING Always disconnect the power and shut off gas supply prior to performing any maintenance on the booster heater to avoid possible personal injury or damage to the booster heater. SWITCH 02. 19. 080. 00 WARNING Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. WARNING If service is required on this unit, contact your Authorized Hatco Service Agent, or contact the Hatco Service Department at 800-558-0607 or 414-671-6350; fax 800-690-2966 or International fax 414-671-3976. WARNING This product has no "user" serviceable parts. To avoid damage to the unit or injury to personnel, use only Authorized Hatco Service Agents and Genuine Hatco Replacement Parts when service is required. FAN 02. 12. 001. 00 Figure 4. [. . . ] Las Vegas 702-649-4616 NEW JERSEY Jay Hill Repair Fairfield Service Plus Flanders 973-575-9145 973-691-6300 402-341-1414 K & D Service Co. Reading RHODE ISLAND Eichenauer Elec. Service Decatur 217-429-4229 Midwest Elec. Service Elmhurst 630-279-8000 Cone's Repair Service Moline 309-797-5323 Marshall Electric Co. [. . . ]