User manual HAUPPAUGE WINTV-D

[. . . ] Select CD-ROM drive and click Next. Remote control receiver with velcro dot fastener WinTV for Windows Installation CD-ROM with: WinTV applications Remote control application Utilities WinTV-D Connectors A/V cable This board and remote are subject to change 4d. You Line out A/V cable - connects between the WinTV board and your sound card (1/8" miniplug), connection to the Center (black RCA) and Surround speakers (white and red RCA) and the auxiliary video input (yellow RCA). Antenna connector Cable TV connector Digital TV output (S-Video) A/V cable connector Remote receiver Remote transmitter Remote control receiver plug Audio Input Remote receiver Video in (yellow) Audio Center (black) Audio Surround 1 (left/white) Audio Surround 2 (right/red) will see a number of files being copied to your hard disk drive. If you receive an error message saying a file cannot be found, browse for these files in the Win98 directory on the WinTV Windows Installation CDROM. Audio adapter - 1/8" miniplug to 1/8" miniplug. Audio extension cable - 1/8" miniplug to RCA red and white male connectors. 4c. Once the Hauppauge WinTV video driver has been detected, click Next. S-Video to composite adapter will convert the WinTV-D S-Video output to Step 1: Prepare your computer Switch off the computer. [. . . ] In cities, a bowtie antenna can often be used if positioned near a window facing the Digital TV broadcaster. Since Digital TV is broadcast over the air, it is necessary to position the antenna to point at the Digital TV transmitter. We have included a utility in the WinTV application to help position the TV antenna. To position the Digital TV antenna, do the following: · Use the supplied list of Digital TV stations to find a Digital TV channel which you know broadcasts in your area. For example, in Cleveland, WKYC broadcasts Digital TV on channel 2. To do this, click on the Suite button on WinTV2000, or click on Configure/Channels/SuiteManager on the WinTV32 application. Click on Tuner to see the Digital TV antenna configuration. Enter the Digital TV Channel Number (for example: 2 for WKYC in Cleveland) and the Channel Name. Make sure Broadcast is set to Antenna, and that Tuner Format is set to DTV-ATSC. Now, to get the diagnostics menu to help orient your Digital TV antenna, hold the CTRL button on your keyboard down while clicking the right mouse button. Keep the right mouse button depressed for a few seconds, and you'll see a menu pop up. · Now slowly rotate your antenna until the Sync Lock and Eq. This indicates that the DTV antenna is pointed to the DTV transmitter. Configuring Surround sound For a basic two speaker system, click on 2 Spkr (L, R). To get enhanced audio, click on Virtual Dolby Mode, then adjust the 3D-Effect, Reverb and Spatial for pleasing results. For a three speaker system, (connect per the instructions in Step 3b) click on 3 Spkr (L, R, C) Dolby 3 Stereo. For a 4 or 5 speaker system, click on 4/5 Spkr (L, R, C, S) Dolby Pro Logic. Step 7: WinTV Software installation After the DirectDraw check completes, WinTV Setup will be run. To use the remote control, make sure · Install the Hauppauge IR Remote Control Application is checked. Click Install to install the WinTV2000 and WinTV-Snapshot applications. After the Setup program is complete, you will see a WinTV2000 icon on your Windows desktop. To run the WinTV2000 application, double click on the WinTV2000 icon. After rebooting your PC, the Remote Control will be enabled. · · Quick Troubleshooting Guide Note: Our web site has information on installing the WinTV and software updates. Find installation tips at: http://www. hauppauge. com/html/sw_wcst. htm. WinTV software updates can be found at: http://www. hauppauge. com/html/98_sw. htm. Step 8: The new WinTV2000 application Scanning for channels When running WinTV2000 for the first time, you will need to scan for your TV channels. [. . . ] Then click OK. - System lockups or error messages when running WinTV2000 Some VGA cards have memory conflicts with WinTV. Also, you can increase the memory range used by the WinTV board in Device Manager. To do this, look under Sound, video and game controllers, double click on the Hauppauge video section, click on Resources, unclick Use Automatic settings and double click on Memory range. In the Edit memory range dialog box, there are small up/down arrows next to Value. [. . . ]