User manual HAWKING HKS104 DOCUMENT

[. . . ] Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his/her own expense. CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. VCCI Mark Warning LIMITED WARRANTY Hawking Technology guarantees that every HKS104 4-port KVM Switch is free from physical defects in material and workmanship under normal use for two (2) years from the date of purchase. If the product proves defective during this two-year warranty period, call Hawking Customer Service in order to obtain a Return Authorization number. [. . . ] The HKS104 KVM Switch is a 4-port PS/2 type KVM Switch that provides compact and integrated all-in-one KVM connectors on the Switch side. It enables users to access, control, boot and reboot multiple computers using only one keyboard, monitor, and mouse. Furthermore, the 3-in-1 KVM cable is tailor-made to integrate keyboard, monitor, and mouse interfaces all into one connector, thus saving a lot of unnecessary time and effort. The HKS104 is an excellent tool for the management of 4 computers on either SOHO or corporate desktop, making it an ideal SOHO solution. It also eliminates the inconvenience and unnecessary effort involved in constantly moving around from one PC to another. Package Contents: One HKS104 4-port KVM Switch Two Sets of 3-in-1 KVM cables One Quick Installation Guide Check to make sure that the unit was not damaged during shipping. If you encounter a problem, contact your dealer. Please read this manual thoroughly, and follow the installation and operation procedures carefully to prevent any damage to the HKS104 unit, and/or any of the devices connected to it. Pre-installation: Note: The default setting for the HKS104 4-port KVM Switch works with most systems. In fact, you do not have to configure anything before installation. It is a plug and play device: First, connect the shared keyboard, video, and mouse to your KVM Switch and then connect PCs to your KVM Switch using the 3-in-1 KVM cable. Then, boot up your PCs one by one, and you can start to operate the KVM Switch immediately!For a quick start on installation and operation, please follow the instructions below. The correct setup sequence is: (1) Connect the shared keyboard, mouse and monitor to the KVM Switch and then connect the KVM Switch to the computers using the slim 3-in-1 KVM cable (with integrated all-in-one connector on Switch side). Power up your connected computers one by one. Since the KVM Switch receives power from the computer's PS/2 interface, it is powered up when you connect the KVM cables to a PC. (2) To set up your HKS104, please follow the steps below: Before connecting any cable to your KVM Switch, please make sure all of your computers and their peripherals have been powered off. Otherwise, the KVM Switch might not be set up properly. Step 1 - Make sure all the computers that are to be connected to the KVM Switch and their peripherals are in the powered-off state. If not, turn the power off before you proceed with the following steps. Step 2 - Connect the shared keyboard, monitor and mouse to the corresponding connectors on the rear of your KVM switch. [. . . ] See Quick Reference Sheet Keyboard hotkeys A keyboard hotkey sequence consists of three specific keystrokes: See Quick Reference Sheet Hotkey sequence = ScrLk + ScrLk + Command key Keystrokes of a hotkey sequence should follow one another within 2 seconds. Otherwise, the hotkey sequence will not be validated. For detailed Hotkey sequences and their corresponding functional commands, please refer to the Quick Reference Sheet. HKS104 4-Port KVM Switch Keyboard Hotkeys/ Push Buttons Operation Command Set Command Hotkey ScrLk + ScrLk + 1 (x) (channel no. ) ScrLk + ScrLk + (arrow up) ScrLk + ScrLk + (arrow down) ScrLk + ScrLk + B ScrLk + ScrLk + End ScrLk + ScrLk + S Any key on keyboar d Push Button Press button x for channel x. -Description Select a PC Select the active channel Next lower channel Select the next lower connected channel Select the next higher connected channel Toggle on/off the beep sound for switching confirmation while autoscanning Reset the KVM Switch for switch system reboot. [. . . ]