User manual HAWKING HNC700PT

[. . . ] Management & Control Software User's Manual Contents Chapter 1 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 1. 1 System Hardware Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 1. 1. 1 Recommended minimum system hardware requirements . . . . . . . . . . . . . . 1-3 1. 2 Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] You can use these two buttons to switch the pages, as shown in Figure 3-22. Use the "Page Up" and "Page Down" key in keyboard could also swith the page. -­ 3-35 Chapter 2 Monitor Switch between cameras Figure 3-22 One-camera Layout When you want to view one individual camera from the multi-camera layout shown in Figure 3-23, double-click on the display frame associated with the dedicated channel in the video area. You will see the size of the display frame is the same as the one-camera layout. Clicking on the "Back" button in the upper-left corner of the video area will switch to the previous selected multi-camera layout. The position for each channel in any layout will be kept for the next time when the layout is selected again for monitoring. -­ 3-36 Management & Control Software User's Manual Back to previous layout Figure 3-23 Single View Mode When in Multi-camera Layout -­ 3-37 Chapter 2 Monitor 3. 6. 3 Input/Output Control Tools PTZ Control Alert Message Digital Input / Digital Output Figure 3-24 Input/Output Control Tool This application software provides another three tools, shown in Figure 3-24 in the bottom-left corner, for controlling the remote Video Server / Network Camera series product of the associated channel. You can click on the dedicated buttons to switch to different control tools that include PTZ (Pan/Tilt/Zoom) control, DI/DO (Digital Input / Digital Output) control and Alert Message receiver. 3. 6. 3. 1 PTZ Control The PTZ (Pan / Tilt / Zoom) tool is shown in Figure 3-25 in the bottom-left corner. If the remote Visual Server/ Network Camera series product associated with the selected channel is connected with a PTZ enabled camera, this PTZ control tool will be activated. You can do PTZ operations, as well as going to the preset location set by the previously user-defined position. You can also apply PTZ control to several cameras simultaneously. See Section 3. 6. 8. -­ 3-38 Management & Control Software User's Manual Tilt up Pan left Zoom out Auto focus Focus near Auto pan Go to the preset location Figure 3-25 PTZ Control Return to Home Pan right Tilt down Zoom in Focus far Auto patrol Stop Auto pan or Auto patrol 3. 6. 3. 2 DI/DO Control After clicking on the "DI/DO" button, shown in Figure 3-26, the control page will be switched to the DI/DO control tool. Only user with root privilege can access the DI/DO control of the remote Video Server / Network Camera series product. In this application software, the color of the channel number indicates the status of the DI (Digital Input) of the channel. You can click on the "Switch button" to change the HI/LOW state of the DO (Digital Output). These features allow you to monitor the remote sensor input from DI and also trigger the remote by the DO switch. Digital input is high Digital input is low Set digital output to LOW Set digital output to HIGH No Connection Figure 3-26 DI/DO Control The color of the DI status is depicted as follows. -­ 3-39 Chapter 2 Monitor OFF When the color of the channel number is gray, that means this channel is not connected to any remote Video Server / Network Camera series product. Red The channel number turns red indicating the DI of the remote Video Server / Network Camera series product associated with the selected channel is in high level. Blue The channel number turns blue if the DI of the remote Video Server / Network Camera series product associated with the selected channel is in low level. 3. 6. 3. 3 Alert Message Figure 3-27 Alert Message If you select the check box for "Enable Motion Detect" or "Enable Digital Input" in the path "Configuration Menu \ Camera Configurations \ Alert Settings", the alert message will show in the window as shown in Figure 3-27; refer to "Alert Settings" in Section 3. 4. 3. An alert message appears in this window when an alert is triggered by user defined motion detection or a digital input level change. You can also use the scroll bar of this box to check on the alert event's history. The message format is described as follows: "time"=>"alert type" #"channel number"("win1", "win2", "win3") -­ 3-40 Management & Control Software User's Manual The message "02:41:00=>MO #1(0, 1, 1)" means that this was a motion detection alert occurred at 02:41:00 AM in Motion Window 2 and Motion Window 3. The message "14:41:56=>DI #1" means there was an alert triggered by the first DI at 02:41:56 PM. 3. 6. 4 Backup Figure 3-28 the Process of Backup Operation "Backup" allow you to copy the recorded video data to another media according to the location and the size you have selected. You can refer to Section 3. 5 "Configuration Menu \ Global Settings \ Backup Settings" for more details on backup settings. From the backed up video data in the media, you can duplicate the backup-data to any removable device, such as CD-ROM, ZIP disk, DVD-RAM, or tape, manually. [. . . ] The speed of exporting data depends on the speed of the computer's processor. During any time of the exporting interval, you can click on the "Transducer" button again to stop the procedure in process. You will get an AVI file from the start time to the time you click on the "Transducer" button. The exported AVI filename will be generated automatically and listed in the fourth column of the status area. [. . . ]