User manual HAWKING HOMEREMOTE HRNC1

[. . . ] 1 Trademarks & Copyright Windows 95/98/ME and Windows NT/2000/XP are registered trademarks of Microsoft Corp. All other brands and product names are trademarks of their respective companies. No part of this publication may be reproduced in any form or by any means or used to make any derivative (such as translation, transformation or adaptation) without the express written consent of the manufacturer as stipulated by the United States Copyright Act of 1976. FCC Certifications This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Please upgrade the firmware via the web user interface. If you want to reset the camera to its default settings, click this button. The default settings of the camera are as follows: Camera Name: "HRNC1" IP Address: "192. 168. 1. 231" Subnet Mask: 255. 255. 255. 0 Administrator Name: "Admin" Password: "1234" Video Port: "5000" Web Port: "85" LED Light Off Users can click on this button to turn off the camera's LED lights. This may help to make the camera less noticeable or to give it the impression that it is not in use when, in fact, it is. Reset to Default 32 6. 2. 11 About About Administrator Utility Version Displays the current version of the Administrator Utility. 33 6. 3 Setting Wizard When you click the "Setting Wizard", a screen will pop up for you to enter the "Administrator Name" and "Password". Name: "Admin" Password: "1234" If the name and password you enter are correct, you can start to setup the camera. 34 Setting Wizard Video Camera Name The default camera name is "HomeRemote Wireless Video Camera". It is recommended that you enter a name for the camera that is easy to remember. IP Address The wizard will automatically set an available IP Address for the camera. For example, if the IP address scheme for your network is 192. 168. 1. x, the wizard will search an unused IP Address between 192. 168. 1. 0 and 192. 168. 1. 254, and assign the camera an available IP Address. You may enter another IP Address to change the setting. Subnet Mask The wizard will auto-search the network's Subnet Mask setting and set the camera to the same Subnet Mask. You may enter another Subnet Mask to change the setting. Gateway The wizard will auto search the network's router setting and set the camera to use the same router. You can enter another router to change the setting. Video Port Cancel Finish This defines the video stream port. The default port number is "5000". Click "Cancel" to quit the Wizard Setting window. Click "Finish" to complete the camera settings. When you finish with the camera settings, you can click "Ok" to run the "Camera Viewer" (i. e. recording software) immediately or click "Cancel" to run the "Camera Viewer" later. 35 7 ­ Camera Viewer (Recording Software) Utility The Camera Viewer (Recording Software) Utility allows users to simultaneously access and view video from up to four cameras. It also allows users to record video manually or by schedule, and playback recorded files. Certain status items for the selected camera, such as frame rate, video received, etc. To install the Recording Software utility, you can follow the same steps you used to install the Admin Utility in Chapter 5 of this user's manual. But this time, simply click on the "Install Recording Software" option. There are three ways to run the Camera Viewer Utility: 1. Click "Start", select "Programs\HomeRemoteVideoCamera\Camera Viewer" to run the utility. Click the "IP Camera Viewer" icon on your desktop to run the utility. 3. Click "Setting Wizard" from Administrator Utility and follow the instructions in the utility. 7. 1 Panel Introduction When you start the Camera Viewer, you will see a Control Panel and a Viewer window with four divisions. 36 37 7. 2 Camera Buttons Camera Buttons Camera If you click on one of these four camera buttons, the Viewer Utility will connect to the selected camera that you want to view and configure. If you want to remove the camera from the viewer, please right click the icon and select "Reset Camera x". [. . . ] A: No, the camera can only be used in Ethernet, Fast Ethernet, or wireless network environments. Q6: Can the camera be connected to the network if it consists only of private IP Addresses?A: Yes, the camera can be connected to a LAN with private IP Addresses. A1: You can adjust the camera's focus manually by rotating the focus ring (see Section 4. 1 LEDs and Focusing). [. . . ]