Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual HELIX X-JUST. We hope that this HELIX X-JUST user guide will be useful to you.
Lastmanuals help download the user guide HELIX X-JUST.
Detailed instructions for use are in the User's Guide.
[. . . ] 1m 3, 5 mm plug alligator clips red/black Signal in / approx. 1m 3, 5 mm plug alligator clips blue/blue Signal out / approx. 1m 3, 5 mm plug RCA plug Dear customer, congratulations on your purchase of this high-quality HELIX product, developed and made in Germany. [. . . ] Connect the other end of the blue , , Signal in" cable to one channel of the amplifier's speaker output terminals using the blue , , Signal in" cable's alligator clips 8 . It is not necessary to pay attention to the correct polarity. Connect the , , Signal out" cable to the X-Just by inserting its 3. 5 mm plug into the X-just , , Output signal" jack 7 . Connect the other end of the , , Signal out" cable 7 RCA plug to one channel of the amplifier's RCA Input jacks. (Note: Use the same amplifier input channel as used for step # 2 above). Connect the red/black , , Power 12V" cable 6 to the X-just by inserting its 3. 5 mm plug into the X-just , , Power 12V" jack. This step has to be taken first before connecting the alligator clips to the power as described in step # 6. Connect the other end of the , , Power 12V" cable 6 to the amplifiers 12V positive (red alligator clip) and ground (black alligator clip) terminals.
Important: The above procedure (step 7-12) calibrated the system. Do not adjust the amplifier input gain or the X-just , , Input Gain Calibration" control further in order to achieve an accurate measurement of the active crossover frequency!
Frequency adjustment
13. Select the crossover frequency range of the X-just by moving the , , 12Hz-180Hz / 0, 1kHz-1, 8kHz / 1, 2kHz-18kHz" switch 4 to the position for the desired crossover frequency. (ie: 90Hz would be in the , , 12Hz-180Hz" range position) 14. Move the , , Off/Calibration/Measurement" switch 5 on the Xjust to the , , Measurement" position. The Red , , Measurement" LED 10 will illuminate. Select the desired crossover frequency by adjusting the X-just , , Frequency" control 3 until the desired frequency is displayed in the X-just LED readout 1 . Switch the amplifiers active crossover on (can be either highpass or lowpass) 17. Adjust the amplifiers active crossover frequency control until the X-just blue , , 0 dB" LED 11 illuminates. [. . . ] Move the , , Off/Calibration/Measurement" 5 switch on the Xjust to the , , Calibration" position. The green , , Calibration" LED will illuminate. Adjust the , , Input Gain Calibration" control 2 of the X-just to its middle position. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE HELIX X-JUST
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual HELIX X-JUST will begin.
