User manual HERKULES G305

[. . . ] Part# 1002753-04 4/23/2008 This manual contains important information concerning the installation and operation of the gun washer listed above. Read manual thoroughly and keep for future reference INSTRUCTIONS Herkules Equipment Corporation 248-960-7100 website: www. herkules. us 2760 Ridgeway Court 800-444-4351 Made in the USA Walled Lake, MI 48390-1662 USA Fax 248 960-7109 e-mail: info@herkules. us Patents USA 7070167 4793369, 4960142, 5174317, 5193561, 5485860 Canada 1299468 & Patents Pending Page 1 of 23 Table of Contents Warnings Assembly Instructions Model Information Installation Operation Preventive Maintenance Troubleshooting Drawings with part lists: Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] For questions or adapter kits contact your paint gun washer distributor. Siphon Feed Guns Place the gun siphon tube on the short stem support. Gravity Feed Guns (HVLP) Place the long stem support over the short stem support. Place paint inlet of gun on long stem support. Place the air cap assembly over the air inlet of the gun to prevent solvent from entering the passage. Pressure Feed Guns Place long stem support over the short stem support. Place paint inlet of gun on long stem support. Pots and Cups Place a pot or a cup on the cup holder. 2) Preparing the Equipment to be washed 1) Remove paint cup or paint line and the air line from the paint gun. Remove all gauges and regulators from painting equipment. Lock the gun trigger in the open position by placing the trigger lock around the gun handle and trigger (see fig. 14). 2) 3) 4) CAUTION All pressure gauges must be removed before placing the equipment in the gun washer to avoid damaging the gauges. Siphon Feed Gun Gravity Feed Gun (HVLP) Air Cap Assembly Long Stem Support Paint Cup Paint Cup Cup Holder Trigger Lock Paint Cup Pressure Feed Gun Short Stem Support Note: Only one gun & one cup shown for clarity. G300 will clean two guns & two cups simultaneously. Clean rinse connections not shown for clarity. fig. 14 Page 14 of 23 Operation Operating the Gun Washer Operating the Manual Brush 1) Make sure wire trigger locks and other accessories are inside the gun washer tank. Place equipment in the tank according to the diagrams shown in fig. 14. 4) 4) Turn the timer knob clockwise 90 degrees to start the gun washer. Turning the timer knob less than 90 degrees will reduce the timing cycle. Paint equipment will clean in 60 to 90 seconds. 5) If the lid is opened prior to the end of the timing cycle, the safety air cutoff switch will stop the gun washer. The gun washer will start again when the lid is closed if time remains on the timer. Note: Open the lid slowly to minimize vapor escape. Remove the equipment from the gun washer and wipe off any remaining solvent. Remove the equipment from the gun washer and wipe off any remaining solvent. 1) 2) 3) 3) Make sure brush is not hanging or pointing out of tank. [. . . ] 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 PN 1001365 Ball Check and 005-145 Ball Check Connector are not shown for clarity. Page 19 of 23 G305 Timer Leg Layout 3 18 17 16 14 7 19 13 11 23 22 2 4 6 15 8 12 10 21 9 1 20 5 Quantity Part # Description 12765 BRACKET FOOT SWITCH ACTUATOR 1 EA. 1002414 STICKER TIMER ON/OFF FOR GUN WASHER 1 EA. 005-155 SCREW BHSC 10-32 X 3/8 BLACK 2 EA. 730-117 HOSE BARB 1/4 X 1/8 NPT BRASS 2 EA. [. . . ]