User manual HILTI DG150

[. . . ] DG150 D GB F Bedienungsanleitung Operating instructions Mode d'emploi 1­10 11­20 21­30 371747 *371747* 1 ³ ² ¶ · º ¾ µ ¿ ´ 2 ¸ ¹ © 21 © 22 3 © 26 © 23 © 24 © 25 © 27 © 28 © 29 DG 150 grinder with DPC20 It is essential that the operating instructions are read before the tool is operated for the first time. Always keep these operating instructions together with the tool. Ensure that the operating instructions are with the tool when it is given to other persons. Contents 1. Declaration of confirmity Page 11 12 13 13 14 16 17 18 18 19 20 See cover Operating controls and component parts of the DG150 ³ On / off switch · Side handle » Guard assemby ¿ Adjusting screw ´ Clamping lever ² Indicator lamp (LED) ¶ Supply cord plug º Speed control switch (settings 1 and 2) ¾ Side handle fastening screw µ Clamping band ¸ Wrench ¹ Clamping nut Diamond cup wheel Lamellar seal, small Clamping flange Lamellar seal, large Retaining ring Spindle Circlip Guard lower section © Guard upper section with hose connector 21 © Spindle lockbutton 22 Operating controls and component parts of the DPC20 23 © Indicator lamp (LED) © Supply cord 24 © Guide rib 25 © Carrying handle 26 © Supply cord holder 27 © Electric socket with cover 28 © Locking lug 29 1. [. . . ] -NOTE- When the extraction hose connector comes into contact with the opened lever, the guard can be rotated further by moving it downwards. 6. 1. 2 Adjusting the guard to the work surface 1. Disconnect the supply cord plug from the socket. Rotate the guard and adjust it to the optimum height. -NOTE- For optimum dust extraction while grinding, the lamellar seal should be almost in contact with the work surface (gap 0 . . . 6. 1. 3 Adjusting the guard for working close to edges The opening in the lower section of the guard can be rotated until part of the cup wheel is exposed. This is of advantage, for example, when grinding close to a wall. - WARNING sThe guard is used in a partly open position for working close to edges. sThe rotating cup wheel presents a risk of serious injury. sWork carefully when the guard is open and close it again when you have finished working at the edge. 5. 8. 3 Protective equipment q Connect the tool to the industrial vacuum cleaner. q Unless stated otherwise in the operating instructions, damaged protective equipment and parts must be correctly repaired or replaced at an accredited service workshop. q For safety reasons, the tool may be operated only when the guard and when safety gloves are worn. q The guard may be adjusted only when the tool has been switched off and the supply cord unplugged. 16 -NOTE- More dust may escape from the guard when working at edges. Disconnect the supply cord plug from the socket. Rotate the upper and lower sections of the guard in opposing directions until they are in a suitable position. Close the clamping lever -NOTE- The guard engages perceptibly in the closed, normal position. -NOTE- If the guard is not held securely when the lever is closed, tighten the clamping band by turning the adjusting screw in a clockwise direction. If the guard cannot be moved when the lever is open, release the clamping band by turning the adjusting screw in a counter-clockwise direction. 6. 2 Side handle 6. 2. 1 Using and adjusting the side handle For safety reasons, the side handle must always be used. It can be adjusted in two axes until in the most favourable working position: ­ Two angled positions for right or left-handed use ­ Pivoted forwards / back in increments 1. Disconnect the supply cord plug from the socket. Release the side handle by turning the clamping screw in a counter-clockwise direction. [. . . ] The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old electric tools for recycling. Please ask your Hilti customer service department or Hilti sales representative for further information. Should you wish to return the electric tool yourself to a disposal facility for recycling, proceed as follows: Dismantle the tool as far as possible without the need for special tools. [. . . ]