User manual HILTI DX 350

[. . . ] Insert th e magazine in th e base of t he handle. Slide it in complet ely until it is f lush w it h the base of t he handle. . . 2. In one movement, pull out t he baseplate and piston sleeve to a stop , then push th em back in again. This cocks t he too l and advances t he magazine. ~&[R?~D~@ DO NOT COCK TOOL AGAINST HAND 4. [. . . ] To remove t he magazine, pull it f rom th e top of t he tool. Check for fo reign matt er in the breech area. 6 Operating precautions Application restrictions 1. NEVER load th e tool unti l you are ready to use it. A LWAYS insert t he fastener before coc king the tool. NEVER cock the tool against th e hand or point th e tool at anyo ne. Keep t he tool pressed against th e work surface for th irt y (301 seconds. If th e booster has not igni ted , wi t hdraw th e tool f rom t he w ork surf ace, ta king care th at it never points at or near you or anyone else. Reposition th e tool against th e wo rk surfac e, push in t o depress th e guid e, and again squeeze th e tri gger. If th e booster st ill has not ignited, wa it anot her t hirty 1301 seconds, remove th e magazine, and imm erse the ent ire magazine in oil or wa te r. Do not atte mpt to use th e remai nder of th e magazine. ALWAYS unload th e tool before: - wo rk breaks - changing part s - cleaning and servicing - sto ring at th e end of th e day. Pay particular attention t o cl eaning the booste r chamber daily. basep late int ernally and externally gu ide. internally and externally piston, extern ally Piston sleeve, internally and externa lly , - ------ - -o III CD to :::l :::l :::l III 0. . . . . :::l :::l III III 3 CD :::l C) CD Steel liner, inte rnally Spray all parts lightly wi t h Hilti Lubr icant befo re reassem bling them. Do not spray th e inside of the st eel liner. t he rnaqazine port on th e tool, For best performance, clea n the tool dai ly or Replacement parts and repair service Warranty Your HILTI powder-actu at ed tool is precision engi neered for safety. NEVER atte mpt to modi fy parts, since thi s can com promise th e built -in safety . Wh en servicing, use only identi cal replacement part s. Replacement part s show n on th e parts list are available th rough your local HILTI representative HILTI operat es a nat ionw ide netw ork of Rapair Centers, and rapid service is a hallmark of th e HILTI system. If your tool requires service or w arranty repairs, contact your local HILTI representative, w ho w ill determ ine w heth er th e tool is f ield repairab le or must be forw arded to th e Repair Center. ISalesmen are not aut horized or equipped to perf orm wa rranty repairs the mselves. ) This new fastening tool is a qualit y produ ct of HILT!. It has been developed thr st udy and research int o const ruct ion fastening meth ods and applicat ions. [. . . ] It has been developed thr st udy and research int o const ruct ion fastening meth ods and applicat ions. reasonable precaut ion has been taken in t he manufacture of t he tool t o assure t complies w it h HILTI's sta ndards of high qualit y. The HILTI tool is warranted for 5 ye ars from t he date of shipment to th e original purchaser. The w arranty is against dE in material or wo rkmanship, provided th at th e system is used in accordance HILTI instructio ns; repairs have not been made by persons ot her t han aut hc HILTI service personnel ; damage is not due to normal w ear and tear ; th e toe not been abused or mi sused; and th e defecti ve to ol is returned to th e local representative for forwarding to th e HILTI Repair Cente r. Part s w hich are found def ectiv e in material or w orkm anshi p w ill be replaced or repaired wi thout cost th an th e cost of shipping and insurance. [. . . ]