User manual HILTI DX 76 PTR

[. . . ] 13 DX 76-PTR 6 9 Hilti Corporation LI-9494 Schaan Tel. : +423 / 234 21 11 Fax: +423 / 234 29 65 www. hilti. com Bedienungsanleitung Operating instructions Mode d'emploi Gebruiksaanwijzing de en fr nl da no sv fi lv lt et 7 Brugsanvisning Bruksanvisning Bruksanvisning Käyttöohje Lietoßanas pamåcîba 8 Instrukcija Kasutusjuhend 14 15 11 12 15 14 16 18 13 Hilti = registered trademark of Hilti Corp. , Schaan W 3249 0308 00-Pos. 1 1 Printed in Liechtenstein © 2008 Right of technical and programme changes reserved S. & O. 384005 / C 384005 *384005* 1 2 6 7 1 +[ +] 3 4 5 67 8 2 2 9 3 Nail Nagel Clou mm 2. 7 green grün vert X-ENP2K X-ENP 19 8 2 3 1 9 2 3. 3 blue blau bleu 6 red * rot * rouge * 10 black schwarz noir > 20 +Ç +| +# +" 1 " "" +± + Cartridge Kartusche Cartouche * Blue cartridges might be used as well for low strength steel up to 10 mm thickness. * Für Standard Stahl bis zu einer Dicke von 10 mm können auch blaue Kartuschen verwendet werden. [. . . ] 7. 4. 5 Checking and adjusting fastener driving depth 3 6 NOTE Fastener driving depth can be adjusted by turning the power regulation wheel on the tool. (setting 1 = minimum; setting 4 = maximum) 1. Use the test gauge to check nail standoff. If a fastener is not driven deeply enough, driving power must be increased. Adjust the power regulation wheel to the next higher setting. If a fastener is driven too deeply, check to ensure that supporting material (e. g. A fastener should not be driven into unsupported sheet metal. Check to ensure that the sheet metal to be fastened lies tightly against the supporting structure, with no gaps or space underneath. 3. Use the test gauge to check nail standoff. If the fastener is still not driven deeply enough or, respectively, is driven too deeply, steps 2 to 4 must be repeated until the correct depth is achieved. If necessary, use a cartridge with a higher or lower power rating. 7. 5 Changing the nail magazine (or fastener guide) 7. 5. 1 Assembly 10 1. Insert the piston brake, the right way round, in the piston guide (or fastener magazine) that is to be fitted to the tool. Insert the piston in the piston guide in the tool. Screw the fastener guide (or fastener magazine) onto the piston guide as far as it will go and then turn it back until it engages. Cycle the tool once with the cycling grip. 7. 5. 2 Disassembly 11 WARNING All cartridges must be removed from the tool. CAUTION After the tool has been in use, the parts to be handled may be very hot. It is essential that gloves are worn if the following maintenance operations have to be carried out before the tool has been allowed to cool down. Check that the tool cycling grip is in its starting position. Unscrew and remove the fastener guide (or fastener magazine). Remove the piston brake from the fastener guide. en 25 8. [. . . ] The piston guide is incorrectly positioned. The tool needs to be cleaned. Remedy See section: 8. 2. 2 Cleaning the piston guide 11 12 13 14 15 See section: 8. 2. 2 Cleaning the piston guide 11 12 13 14 15 Clean the tool. See section: 8. 2. 2 Cleaning the piston guide 11 12 13 14 15 Change the piston and piston brake. Stiff cycling action. en The piston and piston brake have almost reached the end of their service life. The tool is damaged. Contact Hilti. 10. [. . . ]