User manual HILTI DX460

[. . . ] DX460 en Operating instructions 1­17 371665 *371665* 1 3 2 1 0 46 DX 6 45 7 8 9 10 11 15 MX 72 20 13 14 15 16 19 17 18 12 21 14 15 X-460-F810SS 6. 2 X-460-F8N15 X-460-F8N10 X-460-F8S12 X-460-F8SS X-460-F10 XMX72 X-460-F8 X-DNI X-ZF X-SL X-EDNI X-CR X-DAK X-AL-H X-FS X-SW X-M8/X-W8 . . . P10 X-IE X-IE / XI-FV S = X-460-P8 W = X-460-P8W AL = X-460-P8AL 10 = X-460-P10 IE = X-460-PIE IE-L = X-460-PIE-L S/W S/W S/W S S S/W S/W S/W S/W S/W S S S AL S/W S/W S S S/W S/W S/W S S S AL S/W S/W S/W S S S AL S S S 10 10 IE IE-L X-460-FIE X-460-FIE-L 6. 1 1 7. 1 1 7. 7 1 4 1 2 3 2 5 7. 2 2 7. 8 6. 3 3 3 1 2 7. 9 4 7. 3 5 7. 10 90 6 7. 4 1 2 7. 11 7 7. 5 8 1 4 2 3 5 7. 12 90 7. 6 8. 3 1 1 8. 6 1 2 3 2 4 3 2 4 8. 7 1 1 2 2 5 8. 8 2 1 8. 4 8. 9 8. 10 1 2 8. 5 8. 11 8. 12 8. 13 2 3 1 CLICK 8. 14 1 9. 1 2 1 2 2 3 4 3 4 DX 460 powder-actuated tool It is essential that the operating instructions are read before the tool is operated for the first time. Always keep these operating instructions together with the tool. Ensure that the operating instructions are with the tool when it is given to other persons. [. . . ] Repeat until the desired depth of penetration is reached. Use a more powerful cartridge if necessary. aa Fastening with the single-fastener tool 7. 3 1. Press the tool firmly against the work surface at right angles. WARNING q Never attempt to drive a fastener in an existing hole except where recommended by Hilti, e. g. q Never attempt to redrive the same fastener. q Never exceed the maximum fastener driving rate. aa Reloading the single-fastener tool 7. 4 Ensure that no cartridge strip or fastener is loaded in the tool. Remove the cartridge strip by pulling it upwards out of the tool and remove the fastener from the fastener guide. Release the magazine cover by pressing the release button. Pull the magazine cover down as far as it will go. Load a new nail strip into the magazine. Push the magazine cover up until it snaps closed. Load the cartridge strip (narrow end first) by pushing it into the grip from below until flush. If the strip has been partly used, pull it through until an unused cartridge is in the chamber. (The last visible number on the back of the cartridge strip indicates which cartridge is next to be fired. ) When the indicator shows red, or partly red, there are 3 or less nails in the magazine. There are more than 3 nails in the magazine. There are 3 or less nails in the magazine. A strip of 10 nails may be loaded. WARNING q All nails in the magazine must be of the same length. aa Fastening with the magazine tool 7. 6 1. Press the tool firmly against the work surface at right angles. WARNING q Never attempt to drive a fastener in an existing hole except where recommended by Hilti, e. g. [. . . ] The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old powder actuated tools for recycling. Please ask your Hilti customer service department or Hilti sales representative for further information. Should you wish to return the power actuated tool yourself to a disposal facility for recycling, proceed as follows: Dismantle the tools as far as possible without the need for special tools. [. . . ]