User manual HILTI PR16

[. . . ] PR 16 en Operating instructions *373165* 373165 80 0 Y X ³ 300 ¿ » · ´ +X 50 +Y ´ ² º ¶ ¾ PR 16 ¸ µ ¹ I +X +Y 0 50 300 80 1m X 30m Y 50 +Y +X 2m X 150m Y 50 +Y +X Y X 50 +Y +X A 20m 20m A 4mm B 20m 20m B B1 A1 A B B1 A A1 A2 x D1 B D2 B1 B2 A A1 It is essential to read these operating instructions carefully before operating the laser for the first time. Always keep these instructions with the laser. The operating instructions should always be with the laser when it is given to other persons. Laser components PR 16 Rotating Laser 1. Plumb beam (90° to the plane of rotation) 2. [. . . ] Operation 7. 4 Working with the laser detector (accessory) For distances of up to 150m or unfavourable light conditions, the detector (PA 350; available as an accessory) can be used. The laser beam will be indicated visually and audibly. Mount the laser appropriately for the application, e. g. Shortly before levelling is achieved, the laser beam will switch on and rotate (in last mode selected). Depending on the application, stand the laser on, for example, a level surface and level it approximately with the foot screws (with the aid of the spirit level). The X-LED will show green = X-axis is automatically perpendicular and is monitored. The Y-LED will show red = Y-axis can be aligned manually with the servo buttons (laser plane remains perpendicular). 21 7. Operation 7. 6. 1 Inclination/Axis button Used to manually align the X-axis as well (X-LED will change to red). If the manual mode is chosen for the Xaxis and the Y-axis, the laser will no longer be monitored to ensure it remains perpendicular. The Inclination/Axis button can be pressed again to toggle between X- and Yaxes as necessary. The laser has to be switched off and on again to return to the original mode (X-LED = green; Y=LED = red). NOTE If manual (X- and/or Y-) axis setting was the last mode used, within 3 seconds of switching the laser on the Inclination/Axis button can be pressed to retain the last setting. Otherwise the laser will automatically return to the standard mode (X-LED = green; Y-LED = red). 22 7. Operation 7. 7 Working with inclinations 1. Mount the laser appropriately for the application, e. g. Shortly before levelling is completed, the laser beam will be switched on and rotate (in the last mode selected). 7. 7. 1 Inclination/Axis button Used to set the inclination of the X- or Y-axis manually (X- or Y-LED will change to red). If the manual mode is selected for the X- and Y-axes, the laser is no longer monitored to ensure it remains level. The Inclination/Axis button can be pressed again to toggle between X- and Y-axes as necessary. The laser has to be switched off and on again to return to the original mode (X-LED = green; Y-LED = green). NOTE If manual (X- and/or Y-) axis setting was the last mode used, within 3 seconds of switching the laser on the Inclination/Axis button can be pressed to confirm that the last setting should be retained. Otherwise the laser will automatically return to the standard mode (X-LED = green; Y-LED = red). 23 8. [. . . ] Disposal Seperate the individual items as follows: Part, assembly Housing, carrying case Control panel, display Servo motor Electronics Batteries Screws, small parts * Main material plastic plastic metal various alkaline manganese steel Recycling plastics recycling plastics recycling scap metal electronics scrap * scrap metal Dispose of the batteries in accordance with national regulations. Please help to protect and maintain our environment. 31 11. Warranty Hilti warrants that the tool supplied is free of defects in material and workmanship. This warranty is valid so long as the tool is operated and handled correctly, cleaned and serviced properly and in accordance with the Hilti Operating Instructions, all warranty claims are made within 12 months from the date of the sale (invoice date), and the technical system is maintained. This means that only original Hilti consumables, components and spare parts may be used in the tool. [. . . ]