User manual HILTI PRI2

[. . . ] PRI 2 Hilti Corporation LI-9494 Schaan Tel. : +423 / 234 21 11 Fax: +423 / 234 29 65 www. hilti. com Bedienungsanleitung Operating instructions Mode d'emploi Istruzioni d'uso Manual de instrucciones Manual de instruções Gebruiksaanwijzing Brugsanvisning Bruksanvisning Bruksanvisning Käyttöohje Használati utasítás Instrukcja obslugi Návod k obsluze Návod na obsluhu Upute za uporabu Navodila za uporabo Instruciuni de utilizare Kulllanma Talimat> Lietoßanas pamåcîba Instrukcija Kasutusjuhend de en fr it es pt nl da sv no fi el hu pl ru cs sk hr sl bg ro tr lv lt et ja *331423* ko zh Hilti = registered trademark of Hilti Corp. , Schaan W 3277 1206 00-Pos. 1 1 Printed in Liechtenstein © 2006 Right of technical and programme changes reserved S. & O. 331423 / A 331423 1 4 1 9 3 5 4 2 7 8 6 7 5 +± 2 3 + 6 +} " +Ç +] +" +[ +# "± "± "" 7 20 m 20 m "# +| +{ - + "# 180° PRI 2 rotating laser It is essential that the operating instructions are read before the tool is operated for the first time. Always keep these operating instructions together with the tool. [. . . ] c) The user must check the accuracy of the tool after it has been dropped or subjected to other mechanical stresses. d) Check the accuracy of the measurements several times during use of the tool. e) When the tool is brought into a warm environment from very cold conditions, or vice-versa, allow it to become acclimatized before use. f) If mounting on an adapter, check that the tool is screwed on securely. CAUTION If using the rechargeable battery, please read the operating instructions for the battery charger. 6. 2 Indicators LED indicators On/off - blinks green On/off - lights green constantly Slope - lights red constantly On/off blinks red All LEDs blink Battery LED blinks red The tool is leveling itself. The tool cannot begin operation; Cause: The tool has been moved - it cannot level itself. Battery power should last a further approx. 2 hours 16 6. 3 Inserting new batteries 4 1. Open the battery compartment by pressing in and pulling the grip on the battery compartment cover. 2. Insert the batteries in the battery compartment. Close the battery compartment cover. 7. Operation NOTE For further information, please refer to the PRA 22 operating instructions. NOTE The functions "Speed of rotation" and "Line function" can also be controlled directly from the PRI 2 rotating laser. 7. 1 Working with the PRA 2 remote control unit 3 The PRA 2 remote control unit makes working with the rotating laser more convenient and is required in order to make use of certain functions. 7. 1. 1 Selecting the speed of rotation (revolutions per minute) After switching on, the PRI 2 rotating laser always begins to operate at a speed of 150 revolutions per minute. Working at a slower speed of rotation can, however, make the laser beam appear much brighter. The speed of rotation can be altered by pressing the speed of rotation control button the required number of times: 0 > 90 > 150 > 300 >600 >0. 7. 1. 2 Line function The area of the laser beam can be reduced to a line by pressing the line function button. The laser beam then appears considerably brighter. The length of the line can be adjusted by pressing the line function button the desired number of times: 0° > 5° > 10° > 15° > 0°. The length of the line depends on the distance between the laser and the wall or the working surface. [. . . ] In observance of European Directive 2002/96/EC on waste electrical and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility. Dispose of the batteries in accordance with national regulations. 10. Manufacturer's warranty - tools Hilti warrants that the tool supplied is free of defects in material and workmanship. This warranty is valid so long as the tool is operated and handled correctly, cleaned and serviced properly and in accordance with the Hilti Operating Instructions, and the technical system is maintained. [. . . ]