User manual HILTI SDT25

[. . . ] 00 Cover SDT25 P. 1 2. 4. 2004 10:38 Seite 4 SDT 25 SDT 25-15 Bedienungsanleitung Operating instructions Mode d'emploi de en fr 304447 *304447* 00 Cover SDT25 P. 1 2. 4. 2004 10:38 Seite 5 1 1 10 2 9 3 4 8 5 7 6 00 Cover SDT25 P. 1 2. 4. 2004 10:38 Seite 1 2 3 3 3 2 2 3 3 1 1 1 4 4 2 3 5 4 5 2 3 1 7 4 2 5 6 1 00 Cover SDT25 P. 1 2. 4. 2004 10:38 Seite 7 6 1 3 2 7 1 1 8 1 2 4 3 00 Cover SDT25 P. 1 2. 4. 2004 10:38 Seite 8 9 2 2 10 3 1 1 11 2 1 3 4 4 02 BA SDT25/SDT2515 en 2. 4. 2004 10:19 Seite 7 SDT 25 / SDT 25-15 decking tool It is essential that the operating instructions are read before the tool is operated for the first time. Always keep these operating instructions together with the tool. Ensure that the operating instructions are with the tool when it is given to other persons. 1. General information 1. 1 Signal words and their meaning -CAUTIONUsed to draw attention to a potentially dangerous situation which could lead to minor personal injury or damage to the equipment or other property. [. . . ] Avoid unfavorable body positions when working. Work from a secure stance and always stay in balance. To avoid tripping and falling when working, always lead the supply cord, extension cord and extraction hose away to the rear. Concealed electric cables or gas and water pipes present a serious hazard if damaged while you are working. Accordingly, check the area in which you are working beforehand (e. g. Avoid contact between your body and earthed / grounded objects, such as pipes or radiators. External metal parts of the tool may become live, for example, when an electric cable is drilled into inadvertently. 5. 3. 1 Mechanical hazards 5. 3 General safety precautions Use the right electric tool for the job. Do not use the tool for purposes for which it was not intended. Use The tool may jump back if released suddenly when under tension (pressed down), presenting a risk of injury (especially bruising). Release the tool in a controlled manner. Take care when the nosepiece is under tension and the tool is turned upside down. The nosepiece may jump back suddenly, presenting a considerable risk of injury. Follow the instructions concerning care and maintenance. Check that the insert tools used are compatible with the chuck system and that they are secured in the chuck or gear housing correctly. 9 02 BA SDT25/SDT2515 en 2. 4. 2004 10:19 Seite 10 en 5. 4 Requirements to be met by users The tool is intended for professional use. The tool may be operated, serviced and repaired only by authorized, trained personnel. This personnel must be informed of any special hazards that may be encountered. Always concentrate on the job you are doing. Proceed carefully and do not use the tool if your full attention is not on the job. 5. 5 Personal protective equipment The operator and other persons in the immediate vicinity must always wear eye protection and ear protection while the tool is in use. Wear eye protection Wear ear protection 6. Pull the clamping lever out to the front and rotate it to a position where it will not catch on things or get in the way. Pass the supply cord through the strain relief clasp on the grip on the right (feed a loop through from below and then pass it over the clip). Bring the magazine into position at the breach from behind and then engage it with the upper and lower tubular sections. 6. 1 Assembling the tool and electric screwdriver 6. 1. 1 Fitting the grips 1. Open the two clamping levers on the main module. [. . . ] Do not operate the tool if parts are damaged or when the controls do not function faultlessly. If necessary, your electric tool should be repaired at a Hilti repair center. Repairs to the electrical section of the tool may be carried out only by trained electrical specialists 8. 4 Checks after care and maintenance Check that the tool functions correctly (drive and remove a screw) after carrying out care and maintenance. en Remove any dirt adhering to the screwdriving bits and drive spindle and rub these parts with an oily cloth at regular intervals to protect them from corrosion. 8. 2 Care of the tool The tool can be washed under running water if it has become very dirty. [. . . ]