User manual HILTI SF151-A

[. . . ] 00_Cover_SF151_A_P1. qxd 15. 9. 2005 08:35 Seite 3 SF 151-A / SFH 151-A Bedienungsanleitung Operating instructions Mode d'emploi Manual de instrucciones Istruzioni d'uso Gebruiksaanwijzing Brugsanvisning Bruksanvisning Bruksanvisning Käyttöohje Manual de instruções Kasutusjuhend Lietoßanas pamåcîba Instrukcija de en fr es it nl da sv no fi pt el et lv lt ru 227959 *227959* 00_Cover_SF151_A_P1. qxd 15. 9. 2005 08:35 Seite 4 1 6 1 23 57 4 8 9 + 00_Cover_SF151_A_P1. qxd 15. 9. 2005 08:35 Seite 6 2 1 1 2 3 L STOP R 4 5 1 3 2 1 6 2 3 2 1 1 3 SF 151-A / SFH 151-A cordless drill/driver or cordless hammer drill/driver It is essential that the operating instructions are read before the tool is operated for the first time. Always keep these operating instructions together with the tool. Ensure that the operating instructions are with the tool when it is given to other persons. Contents 1. EC declaration of conformity Page 13 14 15 15 16 19 19 21 22 22 23 23 Operating controls and parts 1 @ Quick-release chuck ; Torque and operating mode setting ring = Side handle % Control switch (with electronic speed control) & Forward / reverse switch ( Motor brake ) Two- or three-speed gear selector switch + Type plate § Grip / Battery release button (2 buttons) en 1. [. . . ] Recharge the battery immediately so that it is ready for reuse. Batteries should be stored at room temperature. Never store the battery where it is exposed to direct sunlight or sources of heat, e. g. on heaters / radiators or behind a motor vehicle windscreen. Batteries that have reached the end of their life must be disposed of safely and correctly to avoid environmental pollution. 6. 2 Charging the battery 6. 2. 2 Charging a previously used battery CAUTION Use only the Hilti chargers listed under "Tools and accessories". Ensure that the outer surfaces of the battery are clean and dry before inserting it in the corresponding charger. Read the operating instructions for the charger for further information about the charging procedure. 6. 3 Fitting the battery CAUTION Before fitting the battery, check that the tool is switched off and that the transport lock is engaged (forward/reverse switch in the middle position). Use only the Hilti batteries intended for use with this tool (SFB 150 or SFB 155). Push the battery into the tool from below until it is heard to engage with a click. CAUTION A falling battery may present a risk of injury to yourself or others. Check that the battery is seated securely in the tool. Pull the battery downwards out of the tool. en CAUTION Use only Hilti SFB 150 or SFB 155 batteries. 6. 2. 1 Charging a new battery for the first time A new battery must be charged correctly for the first time before use. This will ensure that the cells form correctly. Incorrect initial charging may have a 7. Operation 7. 1 Setting forward or reverse rotation 3 NOTE The forward / reverse switch is used to select the direction of rotation of the drive spindle. An interlock prevents switching while the motor is running. The control switch is locked when the forward / reverse switch is in the middle position. Push the forward / reverse switch to the right (tool held in working direction) for forward rotation. Push the forward / reverse switch to the left (tool held in working direction) for reverse rotation. [. . . ] Clean the retaining lugs and check that the battery engages securely. Contact Hilti Service if the problem persists. Switch the tool off immediately, remove the battery and contact Hilti Service. The tool has been overloaded (application Use the right tool for the job (don't use a limits exceeded). [. . . ]