User manual HILTI SFH181-A

[. . . ] 00_Cover_SF181_A_P1. qxd 9. 5. 2006 14:44 Uhr Seite 3 SF 181-A / SFH 181-A Bedienungsanleitung Operating instructions Mode d'emploi Manual de instrucciones Istruzioni d'uso Gebruiksaanwijzing Brugsanvisning Bruksanvisning Bruksanvisning Käyttöohje Manual de instruções Lietoßanas pamåcîba Instrukcija Kasutusjuhend de en fr es it nl da no sv fi pt el lv lt et 272635 00_Cover_SF181_A_P1. qxd 9. 5. 2006 14:44 Uhr Seite 4 1 6 1 23 57 4 8 9 + 00_Cover_SF181_A_P1. qxd 9. 5. 2006 14:44 Uhr Seite 6 2 1 1 2 3 L STOP R 4 5 1 3 2 1 6 2 3 2 1 1 3 SF(H)181A cordless drill/driver / cordless hammer drill/driver It is essential that the operating instructions are read before the power tool is operated for the first time. Always keep these operating instructions together with the power tool. Ensure that the operating instructions are with the power tool when it is given to other persons. Contents 1. Manufacturer's warranty - tools 12. [. . . ] on heaters / radiators or behind a motor vehicle windscreen. Batteries that have reached the end of their life must be disposed of safely and correctly to avoid environmental pollution. 6. 2 Charging the battery 6. 2. 2 Charging a previously used battery CAUTION Use only the Hilti chargers listed under "Accessories". Ensure that the outer surfaces of the battery are clean and dry before inserting it in the corresponding charger. Read the operating instructions for the charger for further information about the charging procedure. 6. 3 Fitting the battery to the power tool CAUTION Before fitting the battery, check that the power tool is switched off and that the safety lock is engaged (forward/reverse switch in the middle position). Use only the Hilti batteries approved for use with this power tool. Push the battery into the power tool from below until it is heard to engage with a click. CAUTION A falling battery may present a risk of injury to yourself or others. Check that the battery is seated securely in the power tool. Pull the battery downwards out of the power tool. CAUTION Use only Hilti SFB 180 or SFB 185 batteries. 6. 2. 1 Charging a new battery for the first time A new battery must be charged correctly for the first time before use. This will ensure that the cells form correctly. Incorrect initial charging may have a 19 7. Operation 7. 1 Setting forward or reverse rotation 3 NOTE The forward / reverse switch is used to select the direction of rotation of the drive spindle. An interlock prevents switching while the motor is running. The control switch is locked when the forward / reverse switch is in the middle position. Push the forward / reverse switch to the right (power tool held in working direction) to select forward rotation. Push the forward / reverse switch to the left (power tool held in working direction) to select reverse rotation. 7. 2 Speed selection 7. 2. 1 Speed selection using the 2-speed switch (SF 181-A) 4 NOTE The mechanical 2-speed gear switch can be used to select the speed range required. Speeds with fullycharged battery: 1st gear: 0-390 r. p. m. 7. 2. 2 Speed selection using the 3-speed switch (SFH 181-A) 5 NOTE The mechanical 3-speed gear switch can be used to select the speed range required. [. . . ] Careless disposal may permit unauthorized and improper use of the equipment. This may result in serious personal injury, injury to third parties and pollution of the environment. CAUTION Dispose of defective batteries without delay. Do not attempt to open or dismantle batteries and do not dispose of them by incineration. [. . . ]