User manual HILTI TE 40-AVR

[. . . ] 10 1 11 1 TE 40 / TE 40-AVR Hilti Corporation 2 3 4 2 3 LI-9494 Schaan Tel. : +423 / 234 21 11 Fax: +423 / 234 29 65 www. hilti. com Bedienungsanleitung Operating instructions Mode d'emploi Manual de instrucciones Istruzioni d'uso de en fr es it nl da no sv fi pt el lv lt et 12 1 13 D C B Gebruiksaanwijzing Brugsanvisning Bruksanvisning Bruksanvisning Käyttöohje Manual de instruções A 2 Lietoßanas pamåcîba Instrukcija Kasutusjuhend a. m 7:30 07 Hilti = registered trademark of Hilti Corp. , Schaan W 3161 0107 00-Pos. 1 1 Printed in Liechtenstein © 2007 Right of technical and programme changes reserved S. & O. 274306 / A 274306 *274306* 1 2 4 1 3 3 5 3 4/6 2 2 1 7 6 1 2 4 1 5 5 4 1 3 3 3 2 5 6 2 6 7 1 2 4 1 3 3 2 4 5 4 9 8 7 8 4 1 5 1 3 2 9 3 6 2 TE 40 / TE 40AVR combi hammer It is essential that the operating instructions are read before the power tool is operated for the first time. Always keep these operating instructions together with the power tool. [. . . ] Remove the chuck by pulling it away from the power tool. en CAUTION In accordance with the applications for which it is designed, the power tool produces a high torque. Always use the side handle and hold the power tool with both hands. The user must be prepared for sudden sticking and stalling of the insert tool. CAUTION Use clamps or a vice to hold the workpiece securely. CAUTION The collar at the front end of the gearing section is not to be used as a gripping surface. 7. 1 Preparing for use CAUTION Wear protective gloves when changing drill bits as the drill bit may get hot during use. Release the side handle clamping band by turning the handle counterclockwise. Pivot the side handle into the desired position. Attach the clamp with the depth gauge to the clamping band at the desired position. Adjust the depth gauge to the desired drilling depth. Tighten the screw at the depth gauge firmly. Tighten the side handle securely by turning the grip section. This also clamps the depth gauge in position. 7. 1. 2 Chuck with turn-lock system 7. 1. 2. 1 Fitting the insert tool 4 1. Disconnect the supply cord plug from the power outlet. 25 7. 1. 2. 4 Fitting the chuck 7 CAUTION Remove the depth gauge from the side handle and the insert tool from the chuck in order to avoid injury. NOTE Set the selector switch to the "Chiseling" position before removing the chuck. Disconnect the supply cord plug from the power outlet. Pull the chuck sleeve forward and hold it securely. Remove the chuck by pulling it away from the power tool. 7. 1. 3. 4 Fitting the chuck 11 CAUTION Remove the depth gauge from the side handle and the insert tool from the chuck in order to avoid injury. NOTE Set the selector switch to the "Chiseling" position before removing the chuck. Disconnect the supply cord plug from the power outlet. Grip the chuck sleeve, pull it forward and hold it securely in this position. [. . . ] The power tool doesn't start and the indicator lamp blinks yellow. The power tool doesn't achieve full power. A fault has occurred in the power tool. The carbon brushes are worn. The power tool has not been unlocked (power tools with optional theft protection system). The extension cord is too long or its gauge is inadequate. [. . . ]