User manual HILTI TE6-A

[. . . ] TE 6-A / TE 6-A Li Bedienungsanleitung Operating instructions Mode d'emploi Istruzioni d'uso de en fr it 1 1 TE 6-A 3 5 4 R 36 Volt 2 1 TE 6-A Li 3 5 4 7 6 36 Volt Li-Ion 2. 4 Ah Li-lon 8 CPC 2 7 6 2 R L 3 4 5 4 3 6 2 5 6 2 2 3 3 4 7 + + R R 8 9 10 2 11 + 1 3 12 13 R L 14 15 36 Volt Li-Ion 2. 4 Ah 36 Volt Li-Ion 2. 4 Ah 16 R Li-lon CPC 02_BA_TE6-ALi_P1 en 09. 03. 2006 18:02 Uhr Seite 11 TE 6-A/TE 6-A Li cordless rotary hammer General information It is essential that the operating instructions are read before the tool is operated for the first time. Always keep these operating instructions together with the tool. Ensure that the operating instructions are with the tool when it is given to other persons. 1. Signal words and their meaning -CAUTIONUsed to draw attention to a potentially dangerous situation which could lead to minor personal injury or damage to the equipment or other property. [. . . ] ­ Batteries that have reached the end of their life must be disposed of safely and correctly to avoid environmental pollution. ­ Use the Hilti battery only with the approved Hilti chargers listed in the "Tools and accessories" section. ­ Ensure that the outer surfaces of the battery are clean and dry before inserting it in the corresponding charger. ­ Read the operating instructions for the charger for further information about the charging procedure. Charging a new battery for the first time A new battery must be charged correctly for the first time before use. This will ensure that the cells form correctly. Incorrect initial charging may have a permanent, negative effect on battery capacity. Please refer to the applicable battery charger's operating instructions for information about initial charging. Recharging a NiCd or NiMH battery NiCd and NiMH batteries must be allowed to reach full charge each time they are charged. Recharging Li-ion batteries Li-ion batteries are ready for use at any time, even when only partly charged. Charging progress is indicated by the LEDs; please refer to the section "Battery charge status" (only TE 6-ALi). Fitting the battery to the tool Caution: Before fitting the battery, check that the tool is switched off and that the transport lock is engaged (forward/reverse switch in the middle position). Use only batteries approved for use with the tool. Push the battery into the tool from behind until it is heard to engage with a double click 2. Caution: A falling battery may present a risk of injury to yourself or others. Check that the battery is seated securely in the tool. 16 Operation Fitting the insert tool 1. Check that the connection end of the insert tool is clean and lightly greased. Check that the sealing lip of the dust shield is clean and in good condition. Clean the dust shield if necessary or replace it if the sealing lip is damaged. Push the connection end of the insert tool into the chuck and, while applying slight pressure, rotate the insert tool until it engages in the guide grooves. Push the insert tool further into the chuck until it is heard to engage. [. . . ] Avoid charging the battery in places subject to high ambient temperatures (e. g. at a window) as this has an adverse effect on battery life and increases the rate of self discharge. 02_BA_TE6-ALi_P1 en 09. 03. 2006 18:02 Uhr Seite 19 Manufacturers warranty ­ tools Hilti warrants that the tool supplied is free of defects in material and workmanship. This warranty is valid so long as the tool is operated and handled correctly, cleaned and serviced properly and in accordance with the Hilti Operating Instructions, and the technical system is maintained. This means that only original Hilti consumables, components and spare parts may be used in the tool. [. . . ]