User manual HILTI WSJ 750

[. . . ] WSJ 750/850 Bedienungsanleitung Operating instructions Mode d'emploi de en fr 377834 377834 1 WSJ 750-ET / WSJ 850-ET 1 2 3 4 5 6 14 13 12 11 10 9 1 8 7 WSJ 750-EB / WSJ 850-EB 16 3 15 4 5 6 14 13 12 11 10 9 8 7 16 15 2 1 4 3 2 3 4 2 1 4 2 1 5 3 5 1 6 1 4 3 3 2 2 4 7 1 8 1 2 2 9 10 III II I O 11 5 1 2 3/6 4 3/6 12 1 2/4 13 1 2 3 14 1 2 15 1 2 16 1 4 2 3 5 7 3 4 2 5 7 6 6 WSJ 750-ET / WSJ 750-EB / WSJ 850-ET / WSJ 850-EB orbital action jig saw and WSJ-DRS dust removal system It is essential that the operating instructions are read before the tool is operated for the first time. Always keep these operating instructions together with the tool. Ensure that the operating instructions are with the tool when it is given to other persons. Operating controls and parts On / off switch Lockbutton (only WSJ 750-ET and WSJ 850-ET) Ventilation slots Stroke rate adjustment thumbwheel Dust removal system connector Baseplate Orbital action adjustment lever Baseplate locking screw Guide roller Saw blade (insert tools) Guard Blade holder Saw blade release lever Dust removal hood Low-friction baseplate cover Anti-splinter insert 1. General information 1. 1 Signal words and their meaning -CAUTIONUsed to draw attention to a potentially dangerous situation which could lead to minor personal injury or damage to the equipment or other property. [. . . ] Disconnect the vacuum cleaner hose from the dust removal adaptor. Push the dust removal adaptor downwards and pull it out of the tool. 6. 5 Dust removal hood 6. 5. 1 Fitting the dust removal hood 1. Unplug the supply cord from the electric socket. Push the dust removal hood onto the tool from the front until it engages. Unplug the supply cord from the electric socket. Tilt the dust removal hood slightly and pull it away from the tool toward the front. 6. 6 Sawdust blower The blower keeps the cutting line free of dust and chips by directing a jet of air toward the saw blade. 6. 7 Adjusting the orbital action The four orbital action settings permit cutting performance and quality of cut to be adjusted to suit the material being cut. Orbital action adjustment lever is used to set the tool to one of the four orbital action settings. Please observe the following recommendations: The lower the orbital action setting, the finer and cleaner the cut. The optimum setting can be determined by making test cuts. Setting 0: Setting I: Setting II: SettingIII: No orbital action Low orbital action Medium orbital action High orbital action en -CAUTIONThe cutting edges of the saw blade are sharp. The cutting edges may present a risk of injury. Wear protective gloves. 6. 1 Extension cords If extension cords are used: Use only extension cords of a type approved for the intended purpose and of adequate cross section. Failure to observe this point may result in reduced performance and may cause the cord to overheat. Use only correspondingly marked and approved extension cords for working outdoors. Recommended minimum cross sections and max. cord lengths: Mains voltage Conductor cross section 1. 5 mm2 2. 5 mm2 110 V 230 V 20 m 50 m 30 m 100 m Extension cords for outdoor use For outdoor work use only extension cords approved and correspondingly marked as suitable for outdoor use. Unplug the supply cord from the electric socket. Press the saw blade release lever and hold it in this position. Push the saw blade into the blade holder (teeth facing cutting direction) until it engages. [. . . ] lubricant is applied between the saw blade and workpiece. 21 Fault The saw blade drops out. en 10. Disposal Most of the materials from which Hilti electric tools are manufactured can be recycled. The materials must be correctly separated before they can be recycled. [. . . ]