User manual HITACHI POWER TOOLS DUT13 ELECTRIC TOOL PARTS LIST

[. . . ] 3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Accessories and Attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Carton Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Know Your Drill Press . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] B 2 3 4 5 WARNING For your own safety, never connect plug to power source outlet until all assembly and adjustment steps are completed, and you have read and understood the safety and operating instructions. TOOLS NEEDED Slotted screwdriver Combination wrenche Combination square Framing square Socket wrench with 23 mm. socket 8" & 10" Ajustable wrenches 1 4. Raise the table arm assembly by turning the crank handle (1) clockwise. Place the table (6) in the table arm assembly. Tighten the table lock handle (7). Fig. C WARNING The Drill Press is very heavy and MUST be assembled with the help of 2 PEOPLE OR MORE, to safely assembly it. Place the column (2) on the base, aligning the holes in the column support with the holes in the base. Locate the four long hex bolts (3) from the loose parts bag. Place a bolt in each hole through the column support and the base. Tighten with an adjustable wrench. 6 7 2 1 INSTALLING BATTERY FOR LASER GUIDE (Fig. To prevent damage, make sure the jaws are completely receded into the chuck. NOTE: Clean the taper with a non-alcohol based cleaner before inserting it into the arbor. Fig. H 4 6 7 5 1 2 3 2 NOTE: This drill Press will allow you to reposition the feed handles onto the left hand side of the drill press head (See Fig. Installation is the same procedure as listed above. 1 3 --12 -- 5. Using a rubber mallet, plastic-tipped hammer, or a block of wood and a hammer, firmly tap the chuck upward into position on the spindle shaft. DRILL PRESS ADJUSTMENTS CAUTION: All the adjustments for the operation of the drill press have been completed at the factory. Due to normal wear and use, some occasional readjustments may be necessary. Fig. I WARNING To prevent personal injury, always disconnect the plug from the power source when making any adjustment. Fig. L 6 5 4 INSTALLING LIGHT BULB (Fig. Install a light bulb (no larger than 60 watt) into the socket inside the head. Fig. L) NOTE: The bevel scale has been included to measure approximate bevel angles. If precision is necessary, a square or other measuring tool should be used to position the table. TIGHTEN the nut (4) on the locking pin in the clockwise direction to RELEASE the pin from the table support. Loosen the large hex head bevel locking bolt (5). WARNING To prevent injury, be sure to hold the table & table arm assembly, so it will not swivel or tilt. [. . . ] See Section "ASSEMBLY - TENSIONING BELT" 2. Check tightness of retaining nut on pulley, and tighten if necessary. See Section "BASIC DRILL PRESS OPERATION - SPINDLE SPEEDS" 2. Retract drill frequently to clear chips. [. . . ]