User manual HITACHI POWER TOOLS SV12SE ELECTRIC TOOL PARTS LIST

[. . . ] Use the LEVEL control of channels 9/10 to adjust the volume, since the music signals are mixed to those channels. This connector supplies 5V power to the connected USB device. This connector does not support digital playback from USB devices other than the iPod/iPhone. For playback of such devices, use appropriate stereo mini or RCA pin connectors. [. . . ] Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. Before turning the power on or off for all devices, set all volume levels to minimum. • For the SPEAKERS jacks of the mixer, use only the included MODEL 600S speakers and speaker cables. Use of other types of speakers and cables may result in damage, or even fire. Phantom Voltage +30 V (CH1, 2) Speaker Unit LF: 10” (25 cm) Cone HF: 1. 4” (3. 56 cm) Compression Driver Weight 25. 4 kg (56 lbs) (Speaker 10. 8 kg x 2 + Mixer 3. 8 kg) Package Contents Crossover Frequency 2. 8 kHz Sound is not loud enough …… Are the LEVEL controls of all relevant channels and/or the MASTER LEVEL control set too low?…… the MIC/LINE switch of the Is corresponding channel set to LINE?Turn the LEVEL control to the minimum (zero). Set the switch to the MIC position, then slowly raise the LEVEL control. …… the volume of the connected device Is too low?Raise the volume of the external device. …… the PHANTOM switch set to on when Is using a microphone that requires phantom power? STAGEPAS 600i (includes two MODEL 600S Speakers and a Powered Mixer), Cover Panel, Power Cord (2m), two Speaker Cables (6m), 12 Non-Skid Pads, Owner’s Manual (this booklet) Frequency Range 55 Hz-20 kHz (-10 dB) Maintenance • Remove the power plug from the AC outlet when cleaning the device. Maximum Output Level 129 dB SPL (Measured peak IEC noise@1m) WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. (UL60065_03) P ​ ower ​ onsumption C 35 W (Idle), 100 W (1/8 Power) Coverage Angle 90° (Horizontal)/60° (Vertical) CAUTION Connector Type XLR-3-31 Handling caution • Do not insert your fingers or hands in any gaps or openings on the vents or panel of the mixer and the ports of the speaker. • Avoid inserting or dropping foreign objects (paper, plastic, metal, etc. ) into any gaps or openings on the vents or panel of the mixer and the ports of the speaker. If this happens, turn off the power immediately and unplug the power cord from the AC outlet. [. . . ] • Protective circuit (poly switch) All full-range loudspeakers are fitted with a self-resetting poly switch that protects the high-frequency driver from damage caused by excessive power. If a loudspeaker cabinet loses high-frequency output, immediately remove power from the unit and wait for two to three minutes. This should be long enough to allow the poly switch to reset. Reapply power and check the performance of the highfrequency driver before continuing, with the power reduced to a level that does not cause the poly switch to interrupt the signal. • Interference from cell phones Using a cell phone near the speaker system can induce noise. [. . . ]