User manual HITACHI POWER TOOLS W6VB ELECTRIC TOOL PARTS LIST

[. . . ] DANGER - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS. If the shape of the plug does not fit the power outlet, use an attachment plug adaptor of the proper configuration for the power outlet. Caution Battery pack If the battery pack is mishandled, the battery pack can burst, cause a fire or even chemical burns. · Do not crush and do not expose the battery pack to any shock or force such as hammering, dropping or stepping on it. · Do not short circuit and do not allow metal objects to come into contact with the battery terminals. · Do not expose to high temperature above 60°C (140°F) such as in direct sunlight or in a car parked in the sun. [. . . ] Adjusting it toward + turns the image reddish and adjusting it toward ­ turns the image bluish. 91 AWB (Auto WB) (Daylight) (Shade) (Cloudy) (Tungsten) (Fluorescent) (Flash) The camera automatically detects a light source and adjusts the color tones. If you select an option to suit a specific light source, the color tones are adjusted for the light source (preset white balance). Shooting technique · When you select (Custom), you can register your setting (below). Registering the color tones (Custom white balance) In a scene where the ambient light consists of multiple types of light source, use of custom white balance is recommended in order to accurately reproduce the whiteness. 1 Fn button t [White balance] t 2 Select [ SET] with b/B on the control button, then press the center of the control button. 3 Hold the camera so that the white area fully covers the focus area located in the center, and then press the shutter button down. The shutter clicks and the calibrated values (ColorTemperature and Color filter) are displayed. 92 4 Press the center of the control button. The monitor returns to the recording information display with the memorized custom white balance setting retained. · The custom white balance setting registered in this operation is effective until a new setting is registered. Note · The message "Custom WB error" indicates that the value is beyond the expected range. (When the flash is used on a subject in close proximity or a subject with a bright color is in the frame. ) If you register this value, the indicator turns yellow on the recording information display on the LCD monitor. You can shoot at this point, but it is recommended that you set the white balance again to get a more correct white balance value. To call the custom white balance setting Using the shooting function Fn button t [White balance] t (Custom) Note · If the flash is used when the shutter button is pressed, a custom white balance is registered with the flash light taken into account. Take pictures with the flash in later shootings. 93 Image processing Correcting the brightness of the image (D-Range Optimizer) Fn button t [D-RangeOptimizer] t Select the desired setting (Off) (Standard) No optimization. When there is a sharp contrast of light and shadow between the subject and the background, which is common when shooting into the sun, the camera attenuates the contrast across the entire image to produce an image with proper brightness and contrast. By dividing the image into small areas, the camera analyses the contrast of light and shadow between the subject and the background, producing the image with the optimal brightness and gradation. (Advanced) Notes · (Advanced) is selected when the exposure mode is set to AUTO or one of the following Scene Selection modes: (Portrait), (Landscape) or (Macro). (Standard) is selected when the exposure mode is set to (Sports Action) in Scene Selection. (Off) is selected when the exposure mode is set to (Sunset) or (Night Port. /View) in Scene Selection. · For enlarged RAW images, the effects of the D-Range optimizer other than (Standard) cannot be checked on the camera. · Select to use the continuous selftimer. 98 2 Adjust the focus and shoot the subject. · When the self-timer is activated, audio signals and the self-timer lamp indicate the condition. The self-timer lamp flashes quickly and the audio signal sounds quickly right before the shooting. To cancel the self-timer Press on the control button. Note · When you shoot images using the viewfinder, use the eyepiece cover (page 28). Shooting images with the exposure shifted (Exposure bracket) Using the shooting function Base exposure ­ direction + direction Bracket shooting allows you to shoot several images, each with different degrees of exposure. This camera is equipped with an auto bracket function. Specify the value of deviation (steps) from the base exposure, and the camera shoots while automatically shifting the exposure. You can choose an image that has the brightness you like after shooting is finished. When the flash is fired, flash bracket shooting is used to shift the amount of flash light. To shoot, press the shutter button shot by shot. 1 on the control button t (Bracket: Cont. ) t Select the desired bracket step 2 Adjust the focus and shoot the subject. The base exposure is set at the first shot in the bracket. 99 * (Bracket: Cont. ) Shoots three images with the exposure shifted by a selected step. Press and hold the shutter button until the recording stops. When the flash is fired, press the shutter button shot by shot. is the step currently selected. * _ EV displayed with Notes · When the mode dial is set to M, the exposure is shifted by adjusting the shutter speed. · When you adjust the exposure, the exposure is shifted based on the compensated value. [. . . ] 27 Shutter speed . . . . . . . . . . . . . . . . . . . . . . . . 56, 61 Shutter speed priority . . . . . . . . . . . . . . . . . 61 Single-shot AF . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Slide show . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]