User manual HITACHI 32CX32B

[. . . ] IMPORTANT SAFEGUARDS 1 SOLID STATE COLOR TV OPERATING GUIDE 27CX21B 32CX32B IMPORTANT SAFEGUARDS 2 IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PICTURE CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 REMOTE CONTROL BATTERY INSTALLATION AND REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (See page 35. ) 5 INPUT Button The INPUT button will select between the antenna signal and the video input jacks each time the button is pressed. (See picture below and page 27. ) FOR 32CX32B FOR 27CX21B 6, 7 VOLUME, MUTE Buttons Press the VOLUME up ( ) or down ( ) button until you obtain the desired sound level. HOW TO USE THE REMOTE TO CONTROL YOUR TV 17 To turn the sound off instantly to answer the telephone, etc. , press the MUTE button. Press the MUTE button again or press the VOLUME up ( ) button to restore the sound. MUTE will remain displayed if the CLOSED CAPTION feature is turned off. MUTE will not be displayed if the CLOSED CAPTION feature is on. 8 LAST CHANNEL (LST-CH) Button Use this button to select between the last two channels viewed. (Good for watching two sporting events, etc. ) 9 EXIT/RECALL/COMMERCIAL SKIP (CS) Button Press this button when no menu is displayed, when you want to check the channel being received, or if it has stereo (ST) or second audio (SAP). You can also check the time, CHANNEL ID, and if the SLEEP TIME has been set. When in MENU mode, this button will exit all On-Screen Displays. Press this button twice quickly, when no menu is displayed, to enable the COMMERCIAL SKIP (CS) function. This will tune the TV to the last channel viewed and after 30 seconds, tune back to the original channel. USING THE REMOTE TO CONTROL VCR FUNCTIONS 18 You can also use the RECALL button to quickly clear many of the other On-Screen Display. USING THE REMOTE TO CONTROL VCR FUNCTIONS A detailed explanation of the circled numbers follows on pages 28. Remote Control Illustration Operating the precoded function for your VCR. This remote is designed to operate different types of VCRs. You must first program the remote to match the remote system of your VCR. Aim the remote control at the front of your VCR. Press the VCR button to switch to the VCR precoded mode. While holding down the VCR button on the remote, enter the two digit preset code that matches your VCR as shown on page 31. The remote will turn off your VCR when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your VCR. If the VCR does not turn off after 5 seconds, try a different two digit preset code. If your VCR cannot be operated after performing the above procedures, your VCR code has not been precoded into the remote. In the unlikely event that your VCR cannot be operated after performing the above procedures, please consult your VCR operating guide. The remote control will remember the codes you have programmed in until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure stated above. If your VCR does not have a power function, the remote will issue the CHANNEL UP ( ) function. [. . . ] One is the direct path and the other is reflected from tall buildings, hills or some other objects. Changing the direction or position of the antenna may improve reception. Ghosting may also be caused by defects in the antenna system such as unshielded leads or connecting several sets to the same antenna without using multiple antenna couplers. · SNOW: If your receiver is located in the fringe area of a television station where the signal is weak, your picture may be marred by the appearance of small dots. When the signal is extremely weak, it may be necessary to install a special antenna to improve the picture. USEFUL INFO 35 · RADIO FREQUENCY INTERFERENCE: The interference produces moving ripples or diagonal streaks, and in some cases, causes loss of contrast in the picture. [. . . ]