User manual HITACHI 32LD7200

[. . . ] USER'S MANUAL 32LD7200 Thank you very much for purchasing the HITACHI LCD Monitor. Before using your monitor, please carefully read the "SAFETY INSTRUCTIONS" and this "USER'S MANUAL" so you will know how to operate the monitor properly. You will find it useful in the future. Notes on lnstallation Work: This product is marketed assuming that it is installed by qualified personnel with enough skill and competence. Always have an installation specialist or your dealer install and set up the product. [. . . ] key whilst the swivel display is on the screen. Adjust by using Swiveling angle of the monitor is available within ±30 degrees from the front face. ATTENTION · · · · · · Do not push the panel manually whilst using the swivel function. It could cause damage to the stand or the panel. Do not get on and hang from the monitor. Do not swing the monitor back and forth and around either. Do not put hands or faces close to the monitor whilst operating the swivel function. Use special caution in households where children are present. Do not put any object, like a vase, near the monitor in swiveling area. It would cause a breakage of the object and /or a failure of the stand. Place the monitor on the stable location, or the swivel function would not operate correctly. In the case of using the monitor wall mounted, be sure to detach the connecting cable between the monitor and the stand. Caution when connecting the monitor with the stand · When detaching the stand from the monitor, make sure to detach the connector cable from the stand connection terminal on the rear of the monitor. Pinch right and left locks of the connector and pull out downward. · When attaching the stand to the monitor once again, insert the connector cable into the stand connection terminal on the rear of the monitor. Insert until it clicks. · Make sure that the direction of the connector for stand connecting cable is correct. 23 ENGLISH OPERATING INSTRUCTIONS (continued) OPERATING INSTRUCTIONS (continued) Input Signal Screen Display Input Signal Screen Display The input signal status can be displayed on the screen by pressing the RECALL button of the remote control. · The display will go out in approximately 6 seconds. RECALL button TV 1 ABCDE TV position Name Sound mode Off-timer On-timer Min. VIDEO AV1 Composite Input mode Signal mode Off-timer On-timer Min. RGB H: V: RGB2 RGB 48. 4kHz 60. 1kHz Off-timer On-timer Min. Input mode Signal mode Input horizontal frequency Input vertical frequency 24 RECALL button INPUT SELECT buttons SELECT/ADJUST button (, , , ) CHANNEL UP/DOWN button Displaying MULTI PICTURE Displaying MULTI PICTURE When the MULTI PICTURE button on the remote control is pressed, the screen will display the multi pictures. And then three types of the screen can be selected by pressing the MULTI MODE button on the remote control. The multi-picture mode will change in the following sequence each time the MULTI MODE button is pressed. MULTI MODE button MULTI PICTURE button 2 pictures (Split) 4 pictures 12 pictures Activating the Split mode from the TV screen Pressing the MULTI PICTURE button one time will display 2 pictures. · · · · · · The speaker icon can be shifted left and right by pressing the and SELECT buttons; the audio will be output from the side on which the speaker icon is located. The same signal input cannot be selected for both screens at the same time. The TV channel can be changed by pressing the CHANNEL UP/DOWN button on the remote control. The signal input mode of picture-A or picture-B (the one that the speaker icon is located on) can be selected by pressing INPUT SELECT buttons on the remote control. Pressing the MULTI PICTURE button once again will cancel the multi-picture mode. Refer to the table for 2 pictures (Split) mode. 26 Activating the 4 pictures mode from the TV screen Pressing the MULTI MODE button one time at the 2 pictures mode will display 4 pictures. · · · · · Press and SELECT buttons to select picture A or picture B indicated by a red triangle. For pictures on right, press and SELECT buttons to select picture. The selected input display number would change green. The TV channel can be changed by pressing the CHANNEL UP/DOWN button on the remote control. [. . . ] Stellen Sie das TV-Gerät während des Betriebs nicht auf einen T eppich dadurch können die Lüftungsschlitze unten am Gerät blockiert werden. Das TV-Gerät nur auf einer ebenen Fläche oder einem TV-Sockel (Zubehör) aufstellen. Bei Nichtbeachtung dieser Sicherheitsma§nahmen kann es zur gefährlichen Überhitzung des TV-Geräts kommen, im Extremfall besteht sogar Brandgefahr. sides, rear and top of the television. This is to allow for adequate v entilation. Do not allow soft furnishings, such as curtains to be draped over the TV whilst in operation. Never place the TV onto a carpet during normal operation - this could obstruct ventilation slots on the base of the TV. [. . . ]