User manual HITACHI 42V515

[. . . ] LCD REAR PROJECTION TELEVISION Operating Guide for 42V515 IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 FIRST TIME USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19 THE REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-37 ON-SCREEN DISPLAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The remote will turn off your Audio component when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your Audio component. If the Audio component does not turn off, try a different four digit preset code. The remote will now control your Audio component. Repeat steps 1 - 6 if you wish to program the remote to control another Audio component. 5. 6. THE REMOTE CONTROL 7. NOTES: 1. If your Audio component cannot be operated after performing the above procedures, your Audio component's code has not been precoded into the remote. In the unlikely event that your Audio component cannot be operated after performing the above procedures, please consult your Audio equipment operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. CD precode library is included in the AMP mode. Default device for this mode is Hitachi Audio/Video Receiver (AVR/AMP). INPUTS, Channel (up/down), Volume (up/down) and REC button are not for CD devices. PRECODED AUDIO Buttons These buttons transmit the chosen precoded Audio component codes. EXCLUSIVE TV Buttons These buttons are for operating the TV. GUIDE C. C. MY AUDIO EQUIPMENT CODE IS: CD AMP/RCVR NOTES: 1. The REC (Record) button only applies to some precoded amplifier/receiver codes. Refer to instruction manual of the Audio equipment for operation of the buttons exclusively for the Audio equipment. 34 USING YOUR REMOTE "ENT" BUTTON TO ACCESS THE SPECIFIED INPUT OF THE TV INPUT ACCESS This optional feature allows the user of the remote control to setup it's ENTER (ENT) button to access the specified input of the TV. Setup for this feature is applicable to the remote control's normal mode only and only applies to the DVD, CBL, STB, PVR and AMP modes. Select the desired device mode (DVD, CBL, STB, PVR, or AMP) by using your SOURCE ACCESS buttons ( , LED indicator to the corresponding selection. Hold down the ENTER (ENT) button on the remote and enter the four digit preset code that matches your device as shown on pages 36-37. Then enter the assigned input number (1-5) that the device is related to. If done correctly, the device LED indicator will flash 3 times to confirm proper setup. The remote will now control the desired device. [. . . ] Manufactured under license from BBE Sound, Inc. *SRS and symbol are trademarks of SRS Labs, Inc. SRS technology is incorporated under license from SRS Labs, Inc. Technology HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. [. . . ]