User manual HITACHI 50UX57B

[. . . ] PROJECTION COLOR TV 50UX57B OPERATING GUIDE 60UX57B IMPORTANT SAFEGUARDS 2-4 FIRST TIME USE 5-18 THE GENIUS REMOTE CONTROL 19-30 SET UP CUSTOM VIDEO AUDIO THEATER INFO ULTRATEC BIT-MAP ON-SCREEN DISPLAY 31-58 USEFUL INFORMATION INDEX 59-63 IMPORTANT Follow all warnings and instructions marked on this projection television. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of a sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PROJECTION TELEVISION TO RAIN OR MOISTURE. NOTE: · There are no user serviceable parts inside the television. · Model and serial numbers are indicated on back side of the television. · This television is not intended for use in a computer room. CAUTION: Adjust only those controls that are covered in the instructions, as improper changes or modifications not expressly approved by HITACHI could void the user's authority to operate the TV. MODIFICATIONS: The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hitachi America, Ltd. [. . . ] Set the MULTI-PAGE select switch to VCR. Aim the remote control at the front of your VCR. Hold down the PROG button on the remote, enter the two digit preset code that matches your VCR as shown on page 30. The remote will turn off your VCR when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your VCR. If the VCR does not turn off after five seconds, try a different two digit preset code. The remote will now control your VCR. POWER 5. NOTES: 1. If your VCR cannot be operated after performing the above procedures, your VCR's code has not been precoded into the remote. In the unlikely event that your VCR cannot be operated after performing the above procedures, please consult your VCR operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. If your VCR does not have a power function, the remote will issue the CHANNEL UP function. The MENU button will act as the VCR MENU button for HITACHI VCRs. The LST-CH button will act as your VCR ENTER button if required. The SLEEP button will act as your VCR `100' button if required. The REC button must be pressed two times to begin VCR recording. This button will also act as the VCR record button when the remote is in CABLE or SAT mode. REC STOP PAUSE SLOW PROG. TV/VCR TV/CABLE/SAT VCR LST-CH AUDIO VOL MUTE CH INFO GUIDE EXIT RECALL FAV CH MENU FAV CH L I G H C. S. T SVCS REC SCHED SELECT 1 PRECODED VCR buttons These buttons transmit the chosen precoded VCR codes. EXCLUSIVE TV buttons These buttons are for operating the TV. 2 5 8 0 3 6 9 SLEEP 4 7 INPUT CLU-615MP 27 USING THE REMOTE TO CONTROL CABLE BOX/SATELLITE FUNCTIONS Operating the precoded function for your cable/satellite box. This remote is designed to operate different types of cable boxes and satellite systems. You must first program the remote to match the remote system of your cable/satellite box. Set the MULTI-PAGE select switch to TV/CABLE/SAT. [. . . ] One is the direct path and the other is reflected from tall buildings, hills or some other objects. Changing the direction or position of the antenna may improve reception. Ghosting may also be caused by defects in the antenna system such as unshielded leads or connecting several sets to the same antenna without using multiple antenna couplers. · SNOW: If your receiver is located in the fringe area of a television station where the signal is weak, your picture may be marred by the appearance of small dots. When the signal is extremely weak, it may be necessary to install a special antenna to improve the picture. · RADIO FREQUENCY INTERFERENCE: The interference produces moving ripples or diagonal streaks, and in some cases, causes loss of contrast in the picture. NOTE: The TV set can generate sound distortion in external devices such as a radio. [. . . ]