User manual HITACHI C2565TN

[. . . ] Håll vid skruvindrivning slagborrmaskinen i rät vinkel i förhållande till skruvhuvudet för att skydda skruvhuvudet och/eller skruvdragarspetsen mot skador, och också för att vara säker på att indrivningskraften överförs till skruven. When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following. Read all these instructions before operating this product and save these instructions. Do not use power tools in damp or wet locations. [. . . ] Otherwise the counterforce produced may result in inaccurate and even dangerous operation. Model Voltage (by areas)* Power Input No-load speed Full-load impact rate Capacity: concrete steel wood Weight (without cord and side handle) DH24PA DH24PB *Be sure to check the nameplate on product as it is subject to change by areas. 1 Standard accessories are subject to change without notice. 13 mm Hammer drill chuck For drilling operations when using a straight shank bit for impact drilling with a hammer drill. Anchor setting adapter (SDS-plus shank) (for electric hammer drill) Overall length: 160, 260 mm Anchor size W1/4" W5/16" W3/8" Anchor setting adapter (for manual hammer) Anchor size W1/4" W5/16" W3/8" W1/2" W5/8" 3. Center pin ­ Center pin (A) Center pin (B) Do not use core bits with outer diameter of 25 mm and 29 mm. Core bit (outer diameter) 25 mm 29 mm (A) 32 mm 35 mm 38 mm 45 mm (B) 50 mm with guide plate (The guide plate is not equipped with core bits with outer diameter of 25 mm and 29 mm. Drilling holes and driving screws (rotation only) Drill chuck, chuck adapter (G), special screw and chuck wrench Hammer grease A 500 g (in a can) 70 g (in a green tube) 30 g (in a green tube) Optional accessories are subject to change without notice. Rotation and striking function Drilling anchor holes Drilling holes in concrete Drilling holes in tile Rotation only function Drilling in steel or wood (with optional accessories) Tightening machine screws, wood screws (with optional accessories) dust collector (B) by attaching to drill bits which have 166 mm, 160 mm, and 110 mm overall length. Dump particles after every two or three holes when drilling. Selecting the driver bit Screw heads or bits will be damaged unless a bit appropriate for the screw diameter is employed to drive in the screws. To turn the switch OFF, pull the trigger switch again to disengage the stopper, and release the trigger switch to its original position. Rotation + striking This rotary hammer can be set to rotation and striking mode by turning the change lever fully counterclockwise to the mark. Rotation only The rotary hammer can be set to rotation only mode by rotating the change lever fully clockwise to the mark. 7) To drill wood or metal material using the drill chuck and chuck adapter (optional accessories), proceed as follows. CAUTIONS: Application of force more than necessary will not only expedite the work, but will deteriorate the tip edge of the drill bit and reduce the service life of the rotary hammer in addition. Drill bits may snap off while withdrawing the rotary hammer from the drilled hole. for withdrawing , it is important to use a pushing motion. Do not attempt to drill anchor holes or holes in concrete with the machine set in the rotation only function. Do not attempt to use the rotary hammer in the rotation and striking function with the drill chuck and chuck adapter attached. This would seriously shorten the service life of every component of the machine. Next, mount chuck adapter (D) on the main unit using procedures described in 4 (1), (2), (3), put the tip of the bit in the slots in the head of the screw, grasp the main unit and tighten the screw. [. . . ] (3) Insert the center pin into the guide plate until it stops. (4) Engage the guide plate with the core bit, and turn the guide plate to the left or the right so that it does not fall even if it faces downward. Push it lightly to the wall or the floor straight. Bore after that removing the center pin and the guide plate from core bit. [. . . ]