User manual HITACHI C2868TN

[. . . ] Take some time to read the Operating Guide thoroughly, and if you encounter any difficulty, firstly refer to the Trouble Shooting guide at the rear of this manual. If, in the unlikely event of a problem occurring on your TV, contact your dealer immediately. Use the boxes provided below to record your TV's Model and Serial Nº (these are found on the rating plate located on the rear of the TV). Also, record where and when you purchased this TV. [. . . ] Press MENU to exit. = Select CH = Adjust Menu = Exit Assigning AV Prog. Nºs When AV sockets are commonly used, for example, if you view camcorder recorded events frequently, then we suggest assigning a dedicated program number on your TV. This can be any program number that has not already been assigned. Follow the step by step guide below. Press and HOLD MENU key (20) and select INSTALL. Select MANUAL TUNE from INSTALL menu. Install Autotune Manual Tune Program Sort Language English Use cursor keys 17, 18, 19 or 21 to highlight the AV column of the program number you wish to assign. = Select =Adjust Menu = Exit Once highlighted press the CH key (23) and select between each AV mode using cursor keys 18 or 19. Repeat above to enter other AV sockets or repeatedly press MENU key (20) to store and exit to TV mode. Manual Tune 00 VIDEO 01 BBC2 02 ITV 03 BBC1 04 CH5 05 CH4 06 = Select CH37 AV1 515. 25 528. 30 544. 65 566. 55 572. 10 CH36 AV2 CH = Adjust I I I I I I I Menu = Exit AV2 assigned to Program 7 Page12 Manual T uning cont. Program Naming After Tuning in, most broadcasting station names appear on screen i. e. However, you may change or add program names whenever you desire. To add or change program names follow the simple step by step guide below. Press and HOLD MENU key (20) and select INSTALL. Select MANUAL TUNE from INSTALL menu. Install Autotune Manual Tune Program Sort Language English Use cursor keys 17, 18, 19 or 21 to highlight the Program Name you wish to assign or change. = Select = Adjust Menu = Exit Press the CH key (23) [the first digit will blink], now use cursor keys 17/21 to scroll through all the characters. Once the first character has been entered select next digit using cursor key 19 and repeat above step. Manual Tune 00 VIDEO 01 BBC2 02 ITV 03 BBC1 04 CH5 05 CH4 CH37 AV1 515. 25 528. 30 544. 65 566. 55 572. 10 I I I I I I You may use up to 5 characters for any one Programme Name. Press MENU (20) key to store. Select CH = Adjust Menu = Exit Repeat above steps to assign other Program Names or repeatedly press MENU key (20) to exit to TV mode. BBC2 When selected the character will blink on and off. Page13 Picture and Audio Controls Picture settings are controlled via the TV's on board Menu system. These levels have already been preset at the factory and should require no adjustment. However, your personal viewing preferences may vary from these settings and alteration should be performed as follows:- Press the MENU key 20 on your handset. These Nicam Features features are activated by pressing the key (Nº24) on the handset. When repeatedly pressed the TV will cycle through each mode and will display a particular on-screen symbol. The various modes and on-screen identification is explained below. W ide Stereo This effect produces NICAM digital Stereo This effect enhances NICAM digital stereo sound from the TV. Use this mode for the stereo by forcing a wide area of sound from the TV. Use this mode when viewing action movies or sports events to obtain majority of TV viewing. When selected the STEREO spatialising acoustic performance. When selected the symbol symbol is displayed in the top right hand corner of the shown below appears at the top right hand corner of the TV screen as shown. screen. O O O O Monaural In monaural mode the TV transmits a single sound source. The TV will automatically select this sound when a mono signal is found. Some stereo signals can become poor in adverse weather conditions, and mono should be selected to avoid poor sound. [. . . ] In the unlikely event that this product should develop a fault, we undertake to replace or repair any part of the product which fails due to a manufacturing defect within 12 months of the date of purchase provided that: i) The product has been installed and used only in accordance with the instructions supplied with the product. ii) The product has not been repaired, maintained, or modified by any person other than an Hitachi authorised engineer. iii) The product serial number has not been removed or altered. This guarantee does not apply to product acquired secondhand or for commercial or communal use. [. . . ]